19L236-0143-F1 (100000 - 19Z999) Briggs and Stratton Engine - Overview

Authentic Manufacturer Sourced replacement part used on a variety of Engines. This rocker cover gasket is for the cylinder head. It is sold Individually. It provides a strong seal to protect from leaks. Over time gaskets tend to deteriorate and would need to be replaced.

This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.

Hard starting or an engine that suddenly stops may point to a damaged magneto armature. This ignition coil turns magnetic energy from the spinning flywheel into the electrical pulse that fires the spark plug. First try a known-good spark plug and inspect the safety switches, grounding wire, terminals, and flywheel magnet. Confirm fit from...Read more the full engine identification numbers, since similar coils may mount differently. Work only with the engine off and cool. Disconnect the battery and spark plug lead before removing covers. During installation, use the air gap listed in the service manual and tighten the mounting screws evenly. Keep hands clear of the flywheel and use an insulated tester to check for spark.

This replacement push rod is specially designed for use on Briggs and Stratton engines. It is an authentic part supplied directly from original equipment manufacturer. The push rod is connected to the camshaft to push the exhaust valve open during the exhaust stroke. A bent rod can not only affect your engine's performance, it can serious...Read morely damage other parts if the problem is not taken care of immediately. Please note, this assembly includes the (1) push rod and (1) tappet valve.

This is a genuine manufacturer sourced replacement part designed for lawn and garden equipment engines. This gasket provides an air-tight seal for the float bowl. Over time this gasket will shrink, become brittle and crack allowing for air leaks. At that time it should be replaced. It is made out of rubber material and it is sold individually. Replacing this item you would need a screwdriver.

This genuine part is sourced directly from the original equipment manufacturer. It is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The purpose of this hose is to transfer vacuum from the engine. Unfortunately, over time the material may wear out and begin to crack eventually ...Read morerequiring a replacement. Make sure to check the diagrams of your model for the exact location and the correct installation of this part. Note, this item includes one durable rubber hose and two metal clamps to secure it.

This is a genuine Briggs & Stratton part that is intended to be used with small engines. The fuel pump is used to move fuel from the tank to the carburetor. This part is needed when the carburetor is located above the fuel tank and gravity cannot force the fuel to the carb. The pump uses the vacuum from the crankcase to draw fuel up and o...Read moreut of the tank. This pump is a complete part assembly that includes a fuel line and two clamps.

This is a genuine OEM part. The Briggs & Stratton valve seal is used on many lawn tractor machines. The metal part stops oil from moving into the cylinder from the valve stem. This item is often fastened to the intake valve and the valve keeper. A screwdriver, socket set and wrench set are required for the installation. The metal valve seal is sold individually.

This is a genuine manufacturer-sourced part which is designed for use on lawn and garden equipment. It is an identical replacement for a missing or a damaged clamp that is used to secure the hose. Keep in mind this high-quality product is made of durable metal and is sold individually. Please make sure to check the appropriate diagrams for your model for the correct location and application of this hardware.

This item is a genuine OEM replacement part that is intended to be used with lawnmower engines from Briggs & Stratton and Toro. The metal needle is used as a valve that regulates the amount of fuel sent to the carburetor as the bowl fills and drains. This item is available as an individual replacement part.

This flywheel puller is designed for servicing larger small engines by safely removing tightly seated flywheels without stressing the crankshaft or damaging ignition components. Constructed from heavy-duty steel and engineered to apply even pulling force, it makes accessing the magneto, crankshaft key, or ignition system straightforward d...Read moreuring repairs or overhauls. Built to OEM specifications for durability and precise fit, it’s a reliable tool for maintaining lawn mowers, generators, and pressure washers with compatible engines.

This engine ring set is a genuine OEM replacement designed for small engine applications. It helps seal the cylinder properly to maintain compression, reduce oil consumption, and restore smooth, efficient engine operation. Ideal for engine rebuilds or repairs, this ring set should be replaced when wear causes power loss, excessive oil use, or reduced overall performance.