1932-0 Briggs and Stratton Generator - Overview

The OEM voltage regulator or voltage control is a part used to regulate the voltage so it can provide the right amount of power to electrical components. It attaches inside the alternator housing. The part is black and 2 x 3.5 inches. If damaged, the voltage will become too low/high and the part should be replaced. This part requires a vo...Read moreltmeter to use properly. Please refer to your make, model, and diagram to ensure this is the correct part.

This is an authentic Briggs & Stratton replacement part that is intended to be used with portable generators. The valve is used to connect the fuel line to the tank and to control the flow of fuel from the tank. This item is available as an individual replacement part.

The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is br...Read moreoken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.

This rear bearing cover is designed to protect and insulate the rear bearing of the engine. It is an authentic OEM replacement part with a diameter of approximately 8 inches. It comes with a center/dust cap for easy access to the bearing. The cover acts as a barrier that prevents dirt and other contaminants from entering the bearing and p...Read moreotentially damaging it. It also protects the bearing from harsh environmental conditions and keeps it adequately lubricated. Over time, the cover may crack or break, leaving the bearing exposed. A faulty cover will result in several issues such as excessive noise and vibration, increased friction and wear, overheating, and lower overall equipment efficiency. To complete this repair, pry the center cap off first and then detach the old cover from the rear bearing. Clean the mating surface, align the new cover with the bearing, and snap the center cap into position.

It is an authentic item that is supplied by original equipment manufacturer, it is specially produced for use on Briggs and Stratton and Snapper generators. This kit is used to secure the engine to the main frame, it is designed to help reduce vibrations from a running engine. Over time the material may deteriorate and get compressed caus...Read moreing the generator to vibrate more than usual, if this happens replacing the mount should resolve the issue. It is a complete kit which includes one metal mount with a rubber pad, a screw, and three locknuts. Please note this replacement kit is sold individually.

This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cover. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct par...Read moret. You will require a wrench when replacing this item. This part is sold individually.

The battery charge rectifier goes inside the control box. It is an OEM from Briggs & Stratton for use in generators. This part is sold individually and is made of metal. A wrench and a screwdriver may be required to replace this part. It will need to be replaced if it breaks.

This item is available as an individual replacement part. The outlet is made out of metal and plastic. It may require a wrench during installation. This item will need to be replaced if it breaks. It is a replacement part directly sourced from the manufacturer for use in generators made by Briggs & Stratton and Snapper.

This is a genuine OEM sourced component which is specially designed for use with Briggs and Stratton portable generators. It is an identical replacement for a missing or a faulty vented cap that keeps the fuel inside the tank, please make sure to check the appropriate diagrams of your model for the correct location and application of this...Read more hardware. Keep in mind this high-quality item is made of durable plastic and is sold individually.

This connector is sourced from the original manufacturer as a replacement part for use in generators. The connector has 6 pins/terminals which allow the joining of various electrical cables and components in the generator. Over time the connector can break or wear down, rendering it unable to secure components together. This can result in...Read more electrical hazards, overheating, instability, and loose connections. Disconnect the wires/cables connected to the old connector and remove it from the housing. Place the new connector in the housing and reconnect the wires to the appropriate terminals, following the guidelines in your equipment manual.