1897 - Overview

This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in length. Your machine may have a loud hissing or popping sound coming from the exhaust area if the gasket was faulty. You may also notice th...Read moree presence of black soot around the gasket or the exhaust. Your gasket needs to be replaced if it appears worn or deformed. Otherwise, your machine will experience exhaust leaks. To detach the gasket, remove the fasteners that secure it using a socket or wrench. You can detach the gasket from your machine afterwards. Please bear in mind that this replacement part is sold individually.

A starter solenoid, also known as a starter relay, is an electrical component that is used within small engine systems to control the starter motor by engaging it when an ignition key is turned - acting as a bridge between the battery and starter motor. This starter solenoid is designed for use with various models of lawn mower and other ...Read moresmall engine equipment and is sold as an individual part with no securing hardware. Depending on your model and type of equipment, the location of the starter solenoid may be different, but it is typically located on or around the engine block, and close to the battery. If you notice issues with starting your equipment such as clicking sounds, intermittent starting or simply not starting at all, the solenoid may be burnt or damaged and need replacement immediately. You can test the solenoid for continuity on its terminals with a multimeter, but make sure to take safety precautions. To replace a starter solenoid, you need only disconnect the equipment from power, locate the solenoid, disconnect and remove any connections and securing bolts before you can replace it and test for full functionality.

The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is br...Read moreoken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.

It is a genuine replacement part which is supplied by the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. This is the special screw which has multiple applications depending on the model of your unit, please refer to the appropriate diagrams for the correct location...Read more and use of this hardware. It is a high-quality component which is made of durable metal and it is sold individually.

The set exercise switch attaches to the hour meter. This is a genuine Briggs & Stratton part sourced directly from the manufacturer for use in generators. This part is available as an individual replacement. It is made of plastic and metal and may require a wrench during installation. It might become broken and will need to be replaced.

This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cover. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct par...Read moret. You will require a wrench when replacing this item. This part is sold individually.

This is a genuine Briggs & Stratton replacement part. The gas fuel solenoid is designed by the manufacturer for use in generators. This part is made primarily of metal, and is used to control the flow of fuel to the engine. You may require a wrench when replacing this item. This part is sold individually.

This connector is sourced from the original manufacturer as a replacement part for use in generators. The connector has 6 pins/terminals which allow the joining of various electrical cables and components in the generator. Over time the connector can break or wear down, rendering it unable to secure components together. This can result in...Read more electrical hazards, overheating, instability, and loose connections. Disconnect the wires/cables connected to the old connector and remove it from the housing. Place the new connector in the housing and reconnect the wires to the appropriate terminals, following the guidelines in your equipment manual.