18-2816-49 ((1695522)(2008)) Briggs and Stratton Snow Blower - Overview

This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.

Snow blower discharge chute.

This is an authentic OEM sourced component which is specially made for use with Murray and Snapper lawn and garden equipment. The part provides an identical replacement for a missing or a faulty capscrew that was installed on a new unit. It is a standard hardware which may have multiple applications, please make sure to refer to the appro...Read morepriate diagrams of your model for the correct location and application of this screw. Keep in mind this high-quality hex head capscrew is made of durable metal and is sold individually.

This is a genuine OEM sourced part which is designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The purpose of this hose is to deliver the fuel from the fuel tank into the carburetor. When you press the primer bulb, it will purge all the air out of the carburetor and fill its chambers with fu...Read moreel. The excess fuel is then forced back into the tank through the return line. Over time, lines may wear out and begin to crack eventually requiring a replacement. It includes one durable rubber hose and two metal clamps. Refer to the owners manual and the diagrams of your model for the correct installation of this component. You will need pliers to secure and remove the clamps that secure the hose-primer.

This is an authentic Murray replacement part that has been sourced from the original manufacturer to be used with riding lawnmowers. The metal washer is used to provide spacing between the steering spindle and the front axle assembly. This item is sold individually, please note two washers may be needed.

This is a genuine manufacturer-approved item that is specially designed for Craftsman snowblowers. It is an identical replacement for a missing or damaged knob that was originally installed on a new unit. The purpose of this component is to provide a user with a comfortable grip to secure the adjusting chute. Please make sure to refer to ...Read morethe appropriate diagrams of your model for the exact location and the correct installation of this component. Keep in mind this durable plastic knob is sold individually.

This is a genuine OEM sourced part is specially designed for Murray snowthrowers. It attaches inside the worm gear bracket and moves the chute when the handle is rotated. Over time it may wear out and begin to fail eventually requiring a replacement. Make sure to refer to the owner's manual and the appropriate diagrams for your model to e...Read morensure the correct repair procedure. Note, this high-quality gear-worm is made of durable metal and is sold as an individual component. A wrench set will be needed to perform the replacement.

An authentic replacement part that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It is the special component which is attached to the starter rope to provide a user with a comfortable grip to pull-start the engine. This durable part is made of high-quality plastic and it is sold individually.

This OEM universal joint pin is used within various models of snowblowers to hold the rod and yoke together inside the deflector/chute assembly. If you notice excessive vibrations, clunking, or limited range of motion within the chute mechanism, it is worth inspecting to check for a broken pin or other internal damage. To prevent any futu...Read morere issues with your universal joint pin, make sure to keep it adequately clean and lubricated and inspected regularly. This pin is made of a high-quality metal, measures 1-inch long and .375-inches thick, and is sold as an individual part.

This cable-augur drive is an original part from Murray for dual stage snow throwers and single stage snow throwers. This part attaches to the control lever that is on the control panel, which goes to the lever that is in the drive system. There are no tools that you need to replace this part. This cable-augur drive is made of wire, rubber and metal components. This part is sold individually.

This is a genuine OEM approved replacement primer bulb which is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. By pressing on the purge bulb, it will force fuel into the fuel line from the tank into the carburetor. Once the carburetor is full of fuel, the excess will be sent ba...Read moreck through the return line. Over time the rubber bulb may wear out and crack eventually requiring a replacement to perform its function, please note this high-quality component is sold individually.

This is an authentic replacement part manufactured for use with snow blowers from Craftsman. This part adjusts the tension on the drive cable to engage the drive cable when the user tightens the driver lever. It is recommended to review your models diagram to verify the parts compatibility. This cable tensioner is made of metal and sold individually.