17E842 Graco Paint Sprayer - Overview

This part is available as an individual replacement. The cap attaches to the frame and is made out of plastic. A hammer may be necessary during the installation of this item. Over time this part may break and will need to be replaced. This item is an OEM from Graco for use in sprayers.

The O-Ring is a blue, rubber ring which is used to provide an airtight seal between connected parts, such as between the diffusion tube and filter cap. If the part is broken due to general wear/fatigue, there will be a leak and it should be replaced. Refer to your make, model and diagrams to ensure this is the best part for you.

This is a genuine OEM sourced part which is specially designed for use with Graco sprayers. It is an identical replacement for a missing or a faulty threaded deflector that was included with a new unit, please make sure to refer to the owners manual and the appropriate diagrams of your model for the correct location and application of thi...Read mores component. Keep in mind this high-quality item is made of durable material and is sold individually.

This OEM wheel is constructed of plastic and rubber, and comes in black/white. It attaches onto the axle shaft to provide easy movement. Installation is rated as "Easy" by customers and will require a socket (Tip: Make sure tire is inflated to proper PSI). If the wheel is flat or damaged, then it may be broken and require replacement. Refer to your make, model and diagram to ensure this is the correct part for you.

This is the return hose assembly, or return line, which is designed for various models of airless paint sprayers and is sold as an individual part. The return line is designed to allow paint and pressure to be returned into the reservoir, and simultaneously connected to a specific port on the sprayer for a continuous paint cycle. This ret...Read moreurn line is comprised of a high-quality rubber and metal pump attachment at one end and a metal tube and plastic reservoir attachment at the other end. Depending on your model, you may need a set of pliers or a wrench to disconnect and remove the old line. Before you replace your old line, it is recommended that you wrap the metal end of the line with Teflon tape to create the best seal possible. When replacing the line, disconnect the sprayer from power and release any pressure in the spray gun by squeezing it until no more pressure is felt.

The Manifold Filter Support (Tube, Diffusion) is a black, plastic part which is used to secure the filter. It attaches with the filter mesh and the filter cap. If broken, damaged, or worn it should be replaced. Installation is rated as "Easy" by customers. Refer to your make, model and diagram to ensure this is the correct part for you.

This manifold filter cap repair kit is designed to properly seal the fluid manifold and secure the internal filter in an airless paint sprayer. It includes the essential components needed to prevent leaks, maintain proper filtration, and support consistent spray pressure. Built for durability in high-pressure applications, this kit is an ...Read moreeffective replacement solution for restoring reliable sprayer performance and preventing fluid or pressure loss during professional use.

This transducer is sourced from the original manufacturer for use in paint sprayers. The transducer, also known as a pressure transducer or pressure sensor, is responsible for monitoring and measuring the pressure of the paint being sprayed. The transducer then relays this information to the control system which allows the sprayer to rema...Read morein in the desired spray parameters and prevent over pressurization. Transducers can fail due to electrical issues, or mechanical damage, which can cause inaccurate pressure readings, loss of control, inconsistent spray patterns, poor paint application and fluctuating pressure rates. To remove a faulty transducer first, disconnect the electrical wires and fasteners holding it in place. Position the new transducer in the empty slot and reattach the electrical connections and any mounting hardware to complete your repair.

This replacement gear case insulator is supplied directly from the original equipment manufacturer for use with Graco sprayers. It is an identical substitution for a worn or missing filter that helps to remove the dust and other harmful contaminants from the material. Please make sure to refer to the owners manual for the correct applicat...Read moreion of this component. Keep in mind this high-quality 60 mesh filter is made of durable material and is sold individually.

The packing o-ring fits between the displacement pump and the intake tube. This item is made of rubber and is available individually. This is a genuine Graco replacement part for use in sprayers. A set of pliers may be required to replace this part if it becomes broken.