170705-0675-XX Briggs and Stratton Engine - Overview

This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.

The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "Medium" difficulty and requires a screw driver, wrench set and seal puller. A broken seal will cause a leak, and the part must be replaced. R...Read moreefer to your make, model and diagram to ensure you're choosing the right part. This part comes in black and gray.

Difficulty pulling the starter rope or a cord that stays extended can result from a damaged recoil pulley. This wheel guides and stores the rope while helping turn the engine during starting. Similar symptoms can come from a frayed rope, seized engine, bent starter housing, broken pawls, or weak return spring, so check those items first. ...Read moreMatch the replacement to the full engine model, type, code, and equipment model. Work on a cool engine with the spark plug lead removed. Release spring tension slowly and keep your face and hands clear of the starter housing. Route the rope correctly, confirm smooth return, and reinstall every guard before starting the engine.

Hard starting may come from the recoil system instead of the carburetor or spark plug. If the rope pulls but the engine does not turn, the starter clutch may be worn, dirty, or jammed. The clutch turns the crankshaft during starting and lets go when the engine runs. First inspect the rope, rewind spring, pulley, flywheel screen, and clutc...Read moreh bearing. Confirm fit with the complete engine number. Remove the spark plug wire, wait for hot parts to cool, and keep dirt out of the bearing area. Test free movement before putting the shroud back on.

This item is available as an individual replacement part but also includes the screws. The muffler deflector attaches to the lo-tone muffler and is made of metal. A nutdriver might be required during the replacement of this item. It may become broken and will need to be replaced. This is an authentic Briggs & Stratton and Toro replacement...Read more part that is sourced from the original manufacturer for use with engines, snowthrowers, tillers, lawn mowers, and lawn tractors.

An engine that surges, stalls, or will not stay running can have dirt or worn seals inside its float carburetor. This rebuild kit contains gaskets and small service pieces for restoring the carburetor rather than replacing the complete unit. Inspect the fuel supply and ignition system first, then confirm the engine identification and carb...Read moreuretor design. Work only on a cool engine in a ventilated area. Drain all fuel, disconnect the spark plug wire, and keep sparks and cigarettes away. Photograph the linkages, clean passages without enlarging them, install each gasket in the correct order, and check carefully for leaks before starting the engine.

This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to transfer fuel from the fuel tank to the carburetor, and over time and due to exposure of gas, this fuel line can become brittle and crack, requ...Read moreiring a replacement. If you find your equipment is performing worse, check the fuel line for any visible signs of damage. To replace the fuel line, you will need to disconnect the spark plug and drain the fuel from your equipment, before simply removing the old line and installing the new one and reassembling the rest of the motor.

The exhaust gasket attaches to the exhaust manifold and helps to form a seal. It is an authentic OEM sourced part which is specially designed for use with Briggs & Stratton generators and engines, plus Toro snowthrowers and lawn tractors. This gasket is made of a flexible material and is priced individually. A screwdriver and a wrench may be needed to install this part.

This item is a genuine replacement part that has been OEM sourced and is intended to be used with lawnmower engines from Briggs & Stratton and Toro. The rubber seal is used to prevent oil from leaking at the connection between the bottom of the oil fill tube and the crankcase. This item also allows the fill tube to firmly sit into the case. The dipstick tube seal if available as an individual replacement part.

This spark plug boot is a genuine OEM Briggs & Stratton replacement designed to fit securely over the spark plug, protecting the connection from moisture, dirt, and debris. Its durable, elbow-style design helps ensure reliable ignition and easy installation, making it an ideal replacement when a cracked, loose, or worn boot causes hard starting, misfires, or inconsistent engine performance.

This is a high-quality manufacturer-sourced part which is made for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It helps to distribute the pressure evenly and provide a tight seal for the breather. Over time it may become brittle and begin to crack eventually requiring a replacement. For the proper...Read more application please refer to the appropriate diagrams of your model. This high-quality part is made of durable composite material and is sold individually. You will need a screwdriver and a wrench set to remove and reattach the breather.

This cylinder head gasket is used on small engines to seal the cylinder head to the engine block, maintaining proper compression and preventing leaks of combustion gases and oil. Made from heat-resistant material, it supports reliable engine operation and performance. It’s a direct replacement for worn or damaged gaskets during engine repair or maintenance to restore proper sealing and smooth running.