1696003 (M1529E) Snapper Snow Blower - Overview

This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. This replacement screw is generally used to secure the muffler guard, for correct application make sure to check appropriate diagrams of your model. It is a high-quality Torx screw which is sold individually.

It is an authentic OEM part which is specially designed for Murray, Snapper and Simplicity snowblowers. This bearing secures and stabilizes moving parts to ensure proper rotation angle and position. Unfortunately, over time the components will wear out and may begin to fail eventually requiring a replacement. Keep in mind this high-qualit...Read morey item is made of durable metal and is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware.

This is an original part from Craftsman for use with Craftsman Snowblowers. The fiction wheel assembly meshes with the friction disc, causing the drive wheel axle to turn. The most common reason for replacing the friction wheel is when the snowblower's wheels don't turn.This part is sold individually. Disconnect the spark plug wire before...Read more installing this part. The tools that you will need to replace the friction wheel disc are 3/8" socket, 9/16" socket, adjustable wrench, hammer, 1/2" socket, flat-head screwdriver, and lubrication.

This part is an OEM from Craftsman for use with Snow Blowers. The extension spring is used to provide tension between the link rods, and disconnect arm which slows the riding lawnmower down when the speed control is pushed. The most common reason for replacing the spring is if the drive belt does not have enough tension to engage the auge...Read morer pulley because the spring is broken. This part is sold individually. The tool that you will need to replace the extension spring is a socket wrench.

This item has been sourced from the original manufacturer to be used with lawn tractors from Murray. The metal washer is used with different types of mowers and the application of the washer can vary based on the model of the machine. This washer is sold as an individual replacement part.

It is an authentic OEM sourced item which is specially produced for use with Murray, Snapper, and Simplicity snowthrowers. The axle bearing fits between the axle shaft and the flatwasher and helps to reduce friction. During the installation process, a screwdriver and a wrench set might be needed to replace this part. It may become broken ...Read moreand will need to be replaced. This is made of metal and is available as an individual replacement part.

This hex bolt is sourced from the original equipment manufacturer. The bolt is designed to fasten two individual parts together in your lawn and outdoor equipment. It is made of steel to withstand harsh environmental conditions and measures 0.25 inches in diameter and 0.62 inches in length. The hex bolt gets its name from its hexagon-shap...Read moreed head, which makes it easy to grip with a wrench or socket. Before installing the new bolt, first clean the threaded hole where the bolt rests to remove any dirt or debris in the area. Once the area is clean you can place the bolt in position using your hands and tighten it using a wrench or socket. It is important not to overtighten as this could damage the area and the bolt. Sold individually.

The washer goes between the bearing and the intermed sprocket. It is available as an individual replacement part. This item is an OEM from Murray, Snapper, and Simplicity for use in snowblowers. A wrench might be needed during the installation process. It is made of metal and will require replacing if it bends or breaks.

This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in engines such as those found in snow throwers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws used in the machine. Refer to t...Read morehe parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. This part is sold individually.

Drive Shaft, Hex