1695702 Snapper Snow Blower - Overview

This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.

This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.

Snow blower discharge chute.

This is a genuine manufacturer sourced replacement cap for the fuel tank. It is specially designed for use with Briggs and Stratton engines installed on lawn and garden equipment. It is used to keep the fuel in the fuel tank and protect it from outside contaminants. It features a retainer that will remain in the tank to keep the cap from falling out or getting lost. This plastic cap is sold individually.

This is an original replacement part manufactured for use with Craftsman snow throwers. The special bolt is used to secure the auger blade to the axle. The bolt is used as a safeguard if the blade gets caught or stuck the force will snap the bolt rather than breaking more expensive parts like the auger transmission. The bolts are sold in ...Read morepairs and include the nuts and washers, the bolt sets are sold as individual sets.

This is an OEM replacement part for Briggs and Stratton, Murray, Snapper, and Simplicity engines. When engaged the ignition key starts the lawn tractor. This part is made of metal and is sold in a set of two. There are no tools needs to use this part, as it comes pre-assembled and really to use.

This is a genuine manufacturer-approved item that is specially designed for Craftsman snowblowers. It is an identical replacement for a missing or damaged knob that was originally installed on a new unit. The purpose of this component is to provide a user with a comfortable grip to secure the adjusting chute. Please make sure to refer to ...Read morethe appropriate diagrams of your model for the exact location and the correct installation of this component. Keep in mind this durable plastic knob is sold individually.

This authentic replacement part is designed for use with Murray, Simplicity and Snapper snowblowers. Flange bearings are used to provide support for a shaft while reducing friction between rotating parts. The rollers take the load and spin, distributing the weight evenly while the minimal contact area of the roller reduces friction. Beari...Read morengs experience constant wear from pressure, heat, vibration, and friction. Because of this, many bearings need to be periodically replaced. Make sure to check the diagrams of your model for the exact location and the correct installation of this component. It is sold individually. You will need a screwdriver and a wrench set to take apart the housing in order to gain access to this flange bearing. Keep in mind the screws utilized to secure this component are sold separately.

This handle is an original part from Craftsman for snow blowers. This part connects to the frame for steering and pushing the snow blower. You will need a wrench or an adjusting wing knob (part 1501260MA) to replace this handle. This part is made of metal and sold individually.

It is a genuine OEM sourced part that is specially produced for use with Murray and Snapper lawn and garden equipment. This is a standard hardware which may have multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component. This high-quality carriage ...Read morebolt is made of durable metal and is sold individually, keep in mind the washer and other parts are all sold separately.

This is a genuine Murray, Snapper, and Simplicity part sourced directly from the manufacturer for use in snowthrowers. The clutch spring boot is made out of rubber. A set of pliers may be necessary during the installation of this item. It may become broken and will need to be replaced. This is available as an individual replacement part.

This is a genuine replacement part manufactured for use with outdoor power equipment. The special nut is used with a variety of types of equipment and the application of the nut varies depending on the model of equipment. This nut is available as an individual replacement part, please see model diagram for the nut\'s location and usage.