169551 Snow Blower - Overview

This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.

This 5/16-18 wing knob is sold individually. It is a plastic part, black in color, that works on a variety of equipment. Its general function is to allow you to quickly loosen, remove, or fold down things such as handles. If it no longer loosens or tightens, it may be broken or damaged due to fatigue and wear. Replacing this part is an easy repair that does not require any tools.

This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.

This Fuel Filter is a white plastic part attached within the fuel delivery system between the fuel tank and carburetor. Installation is rated as "Easy" and requires a set of pliers and a screwdriver. If broken, there may be a leak or blockage and the part should be replaced. The part may also need to be replaced according to manufacturer'...Read mores specifications, and is a manufacturer-approved part. Refer to your make, model and diagrams to ensure this part is correct.

Snow blower discharge chute.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. This replacement screw is generally used to secure the muffler guard, for correct application make sure to check appropriate diagrams of your model. It is a high-quality Torx screw which is sold individually.

This is an authentic OEM sourced driver belt, not an aftermarket equivalent. It is specially designed for a variety of snow throwers. This is the main drive belt for the unit that will spin the augers. Please make sure to check appropriate diagrams for correct location and application of this item. It is made from durable rubber material ...Read moreand it is sold individually. You would need a set of wrenches to complete this repair.

This hex nut is a fastener made from steel and is used to secure the end of a bolt in various lawn and garden equipment and machinery. It is a genuine OEM replacement part that comes in a standard size of 5/16 of an inch with 18 threads per inch. The hex nut has a hexagonal shape, which gives it greater grip and makes it easy to tighten u...Read moresing a wrench or a set of pliers. The nut also has a flange on one end, which locks the nut in place, prevents damage to the area where it is installed, and allows the load to be evenly distributed. It is important to replace your hex nut if it is loose, cracked, or corroded. If you have not yet removed the old hex nut from your equipment you will need a socket wrench to remove it. After that, you can easily install the new nut by threading it onto a bolt or screw and then tightening it with a wrench or pliers until it is tightly secured.

This Auger Drive Belt is an original part from Craftsman for use with Craftsman Snowblowers. The auger drive belt rotates the auger on the snowblower. The most common reason for replacing the drive belt is when the snowblower auger won't turn.This part is sold individually. Her is a list of tools that are needed to replace the auger drive belt are a 3/8 inch socket, 9/16 inch wrench, adjustable wrench and a clamp.

The hair pin is a silver, metal pin used to secure and lock parts in place. If broken, the part being secured will come loose and the pin should be replaced. This is an OEM part directly from the manufacturer. Most customers rated the replacement of the hair pin as an easy repair.

This is an authentic manufacturer-sourced item that is specially designed for Murray and Simplicity snowthrowers. It connects the control lever to the clutch in the drive system allowing a user to engage and disengage the unit. Please note this durable rubber insulated metal clutch cable is sold individually. Make sure to refer to the app...Read moreropriate diagrams of your model for the correct location and application of this component.

It is an authentic OEM part which is specially designed for Murray, Snapper and Simplicity snowblowers. This bearing secures and stabilizes moving parts to ensure proper rotation angle and position. Unfortunately, over time the components will wear out and may begin to fail eventually requiring a replacement. Keep in mind this high-qualit...Read morey item is made of durable metal and is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware.