169237 Simplicity - Overview

This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.

This cotter pin is an OEM part that is 1.25 inches long, gold in color, and sold individually. Made of metal, it can have a range of applications on a variety of lawn and garden equipment. Generally, you will need to replace this part if it becomes broken due to age and wear, or if you need to remove it for making other repairs. This is...Read more an easy repair that only requires a pair of pliers to carry out. You need to bend one end around the shaft or bolt and bend the other around the back end of the bolt to complete the repair.

This Ball Bearing is an individually sold, silver/black, metal part. It reduces friction in the spindle assembly between the spindle shaft and the spindle housing. If broken due to wear/fatigue, you will hear a grinding, growling, rumbling or screeching sound, and should replace the part. Refer to your make, model and diagrams to ensure this is the right part for you.

It is an OEM item which is made for use with Murray, Snapper, and Simplicity lawn mowers. This gasket provides a tight seal for the arbor housing. Over time the material will wear out and it may get compressed eventually requiring a replacement to ensure the unit functions properly. Refer to the specific diagrams of your model for the exa...Read morect location and the correct installation of the new part. It is a high-quality gasket which is made of a durable foam material and is sold as an individual component. You will need a wrench set to take apart the housing and gain access when replacing this gasket.

This genuine OEM part is compatible with a variety of Snapper, Simplicity, and Murray tractors/mowers. Bearings allow moving parts (axles and wheels in this case) free motion and steady operation. They stabilize directional motion while reducing friction between moving parts. Bearings are high wear parts which often need regular replacement to function at their peak. Sold separately.

This hex nut is a fastener made from steel and is used to secure the end of a bolt in various lawn and garden equipment and machinery. It is a genuine OEM replacement part that comes in a standard size of 5/16 of an inch with 18 threads per inch. The hex nut has a hexagonal shape, which gives it greater grip and makes it easy to tighten u...Read moresing a wrench or a set of pliers. The nut also has a flange on one end, which locks the nut in place, prevents damage to the area where it is installed, and allows the load to be evenly distributed. It is important to replace your hex nut if it is loose, cracked, or corroded. If you have not yet removed the old hex nut from your equipment you will need a socket wrench to remove it. After that, you can easily install the new nut by threading it onto a bolt or screw and then tightening it with a wrench or pliers until it is tightly secured.

Sold as a kit, including the metal body switch, a pair of keys, and the required hardware, this Ignition Switch Assembly has been sourced directly from the original manufacturer. If you are unable to start and stop your engine, you may need to replace the Ignition Switch Assembly. To complete this repair, you will need a screwdriver, a wrench set, and pliers. Customers rate this repair as Easy.

The hair pin is a silver, metal pin used to secure and lock parts in place. If broken, the part being secured will come loose and the pin should be replaced. This is an OEM part directly from the manufacturer. Most customers rated the replacement of the hair pin as an easy repair.

This centerlock nut, or lock nut, is sold individually and locks itself in place when inserted, to prevent it from backing out due to vibration. Over time, due to its strenueous job, it may become loose or break due to wear and tear, and will need to be replaced. This lock nut is made of metal and is silver in color. When it will no longe...Read morer lock, you will need to complete this easy repair, which requires a wrench or socket and torque wrench. Ensure you torque the lock nut to your manufacturer specifications; this nut can have a range of different applications for a variety of equipment, so please check your model number or owners manual to be sure it is the right fit for your model.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Murray, Snapper and Simplicity lawn mowers. This is an identical replacement for a missing or damaged housing-arbor top that was originally installed on a new unit, please make sure to check the appropriate diagrams and the owners manual f...Read moreor the correct location and application of this component. Keep in mind this high-quality item is made of durable metal and is sold individually.

This is a genuine replacement part for tractors made by Snapper, Murray, and Simplicity. The bushing fits between the washer and the mounting steering plate. It is made out of plastic and will need to be replaced if it becomes broken. A screwdriver, a set of pliers, and a wrench set may all be needed to help replace this part. This item is sold individually.

Sourced directly from the original equipment manufacturer, this Spring Washer is used to spread the load under a bolt or nut. It has an I.D. of 0.475 inches, is made of metal, and is sold individually, not as part of a kit or assembly. If you notice any signs of corrosion, cupping, wear, or damage, you will need to replace the Spring Wa...Read moresher. Refer to your owner's manual to determine the exact location of this part on your model.