169- Cub Cadet - Overview

This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.

Hard starting or an engine that suddenly stops may point to a damaged magneto armature. This ignition coil turns magnetic energy from the spinning flywheel into the electrical pulse that fires the spark plug. First try a known-good spark plug and inspect the safety switches, grounding wire, terminals, and flywheel magnet. Confirm fit from...Read more the full engine identification numbers, since similar coils may mount differently. Work only with the engine off and cool. Disconnect the battery and spark plug lead before removing covers. During installation, use the air gap listed in the service manual and tighten the mounting screws evenly. Keep hands clear of the flywheel and use an insulated tester to check for spark.

This is a manufacturer approved starter pinion gear designed for use with lawn and garden equipment engines. This Starter pinion gear is attach to the starter clutch drive and engages the flywheel to start the engine. It is made out of Plastic and Aluminum and it is Sold Individually.

This fuel line is compatible with several different makes and models of small engine equipment and is sold as an individual part. Equipped with the securing clamp, this rubber fuel line is used to transfer fuel from the fuel tank to the carburetor, and over time and due to exposure of gas, this fuel line can become brittle and crack, requ...Read moreiring a replacement. If you find your equipment is performing worse, check the fuel line for any visible signs of damage. To replace the fuel line, you will need to disconnect the spark plug and drain the fuel from your equipment, before simply removing the old line and installing the new one and reassembling the rest of the motor.

This replacement filter-pre cleaner is a genuine OEM sourced item, not an aftermarket imitation. It is a high quality item commonly utilized on Briggs and Stratton engines. This item adds a extra layer of filtration for the unit. This foam pre-cleaner is sold individually. Please note, the main pleated paper filter is sold separately. Yo...Read moreu will need a screwdriver to replace this item. • Remove the filter cover • Take out the old filter • Secure the new cleaner • Secure the cover

The Jamlock Nut is a 3/8-16 inch metal nut which can be installed using a socket or wrench set. It's used to secure and lock parts in place. If the part is damaged and comes loose it should be replaced. This is an authentic part authorized by the manufacturer.

This is an authentic Briggs & Stratton replacement part sourced from the original manufacturer for use with small engines. The special screw includes a washer and is commonly used to secure the engine's exhaust manifold. The screw is available as an individual replacement part.

It is an authentic OEM supplied part that is designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. This part provides a seal for the tappet valve. It is an identical replacement for a missing or a faulty part that was included with a new unit. Please make sure to check the appropriate diagrams ...Read moreof your model for exact location and application of this component. Keep in mind this high-quality valve seal is sold individually.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. This special gasket is utilized to provide an air-tight seal between connected components, please make sure to refer to the appropriate diagrams of your model for...Read more the correct location and application of this hardware. Keep in mind over time the material may wear out and crack eventually requiring a replacement. It is a high-quality item which is made of durable composite material is sold individually.

This is a genuine manufacturer-sourced part which is designed for use on lawn and garden equipment. It is an identical replacement for a missing or a damaged clamp that is used to secure the hose. Keep in mind this high-quality product is made of durable metal and is sold individually. Please make sure to check the appropriate diagrams for your model for the correct location and application of this hardware.

It is an authentic manufacturer sourced replacement part that is specially designed for use with Briggs and Stratton engines installed on generators and lawn and garden equipment. This gasket provides an air tight seal between the carburetor and the manifold. Over time gaskets tend to deteriorate and crack eventually requiring replacement. It is made out of high-quality composite material and it is sold individually.

This is a genuine manufacturer-approved replacement part which is specially designed for use on Briggs and Stratton engines commonly installed on lawn and garden equipment. The push rod rides on the camshaft to push the exhaust valve open during the exhaust stroke. A bent rod can not only affect your engine's performance, it can seriously...Read more damage other parts if the problem is not taken care of immediately. Keep in mind this high-quality part is made of durable metal and is sold individually.