1678-0 Briggs and Stratton Generator - Overview

Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve and the rubber cap. Its primary purpose is to deliver fuel from the tank to the carburetor. This part is found on the underside of the fuel...Read more tank and should be replaced when it is worn or damaged. When malfunctioning, it may cause your engine to be starved of fuel and run rough or not at all. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.

This OEM replacement fuel gauge cap is designed for use in generators. It comes in a cylindrical shape and has a built-in window to easily view the fuel levels without pulling out the entire cap. It is approximately 5.25 inches in length, while the head has a diameter of 3 inches. The purpose of the cap is to cover and protect the fuel ga...Read moreuge, which indicates the levels of gas available in the tank. It prevents dirt and debris from entering the gauge area and prevents fuel from leaking out. A faulty cap will allow contaminants to enter the gauge, and cause fuel to leak, leading to inaccurate fuel readings and safety risks. Twist the cap to remove it and clean the surrounding area thoroughly. Place the new gauge cap in position and ensure that it is locked in place.

This circuit breaker is an important safety device found in the control box of your generator. It protects the electrical system from overloads and short circuits by automatically cutting off the electricity flow when it detects excessive current. It can handle a maximum current of 20 amps. You can tell if a circuit breaker is broken by c...Read morehecking for visible signs of damage, such as an unresponsive button, cracks, or burnt marks. If the circuit breaker repeatedly trips, the breaker may be faulty or overloaded. You will need a screwdriver, a set of pliers, a socket set, and a nutdriver to replace the breaker in your generator. Follow the instructions in your user manual to access the control box. You typically need to remove the carburetor and the fuel tank before removing the cover of the control box. Please note that this OEM replacement part is sold individually.

This is an authentic OEM part from Briggs and Stratton and Snapper for use with Generators. The fuel tank mounting grommet forms a cushion between the fuel tank and the fuel tank mounting bolts. The most common reasons for replacing the grommet is if the fuel is leaking from the fuel tank, the fuel lines are loose at the tank or the rubbe...Read morer grommet is cracked and not sealing. This part is made out of rubber and is sold individually. Here is a list of tools that are needed to replace the grommet a receptacle for draining fuel, a wire hook (to retrieve fuel lines), screwdriver, wire cutters or scissors.

The brush holder assembly in your generator keeps the brushes in place, allowing them to touch the rotor. It consists of a plastic brush holder and two carbon brushes with lead wires and attached springs. You can usually find the holder assembly inside the generator housing, near the rotor and stator assembly. If the holder assembly is br...Read moreoken, it can cause improper electrical contact between the brushes and the rotor, leading to a loss of electrical current transfer. Additionally, over time, the brushes will wear down from use, resulting in inconsistent contact with the rotor. Look for visible signs of damage like cracks, breaks, or deformations in the holder. A damaged holder can cause unstable voltage, power surges, or your generator failing to generate electricity altogether. To remove the existing brush holder assembly from your generator, refer to your user guide for detailed instructions. It may involve removing a cover or access panel to reach it. Use a nut driver or suitable tool to disconnect the assembly from the rear-bearing carrier and any connected wires. Remember to magnetize the brush assembly and conduct a generator test after installing the new one. Please keep in mind that this authentic OEM part is sold individually.

This is a genuine manufacturer-sourced replacement part which is designed for use with Snapper and Briggs and Stratton portable generators. Over time batteries will become weaker and eventually will not provide enough power to operate the equipment as it was designed. Several factors can cause this, such as improper charging or the way th...Read moree unit is used along with normal deterioration of the battery. Note, this high-quality battery is sold individually. Refer to the owner's manual for the correct application.

This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cover. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct par...Read moret. You will require a wrench when replacing this item. This part is sold individually.

This is a genuine OEM supplied part that is specially designed for Briggs and Stratton portable generators. The item provides an identical replacement for a faulty or a missing power regulator assembly that was installed on a new unit. It is made of high-quality materials and is sold as an individual item. Refer to the owner's manual and the appropriate diagrams for your model to ensure the correct repair procedure.

The battery charge rectifier goes inside the control box. It is an OEM from Briggs & Stratton for use in generators. This part is sold individually and is made of metal. A wrench and a screwdriver may be required to replace this part. It will need to be replaced if it breaks.

This is available as an individual replacement. The outlet is part of the control panel assembly. When replacing this item a wrench may be needed. It is made of metal and plastic and will need to be replaced if it becomes broken. This is an authentic Briggs & Stratton and Snapper replacement part that is sourced from the original manufacturer for use with generators.

The manufacturer certified M8 Flange Nut is an 8mm silver, serrated, metal part. It can be installed using a wrench or socket, and is used to secure parts in place and secure the load. If broken or damaged, the nut and part may be loose and it should be replaced. Check your make, model and diagram to ensure you are choosing the correct part.

This item is available as an individual replacement part. The outlet is made out of metal and plastic. It may require a wrench during installation. This item will need to be replaced if it breaks. It is a replacement part directly sourced from the manufacturer for use in generators made by Briggs & Stratton and Snapper.