1655-0 Briggs and Stratton Generator - Overview

Made of durable rubber and plastic components, this Fuel Valve and Bushing are designed for use in over 150 models of generators and pressure washers. This item is sold as a kit, including the valve and the rubber cap. Its primary purpose is to deliver fuel from the tank to the carburetor. This part is found on the underside of the fuel...Read more tank and should be replaced when it is worn or damaged. When malfunctioning, it may cause your engine to be starved of fuel and run rough or not at all. You will need a screwdriver and pliers to complete this repair. Customers rate this repair as Easy.

This circuit breaker is an important safety device found in the control box of your generator. It protects the electrical system from overloads and short circuits by automatically cutting off the electricity flow when it detects excessive current. It can handle a maximum current of 20 amps. You can tell if a circuit breaker is broken by c...Read morehecking for visible signs of damage, such as an unresponsive button, cracks, or burnt marks. If the circuit breaker repeatedly trips, the breaker may be faulty or overloaded. You will need a screwdriver, a set of pliers, a socket set, and a nutdriver to replace the breaker in your generator. Follow the instructions in your user manual to access the control box. You typically need to remove the carburetor and the fuel tank before removing the cover of the control box. Please note that this OEM replacement part is sold individually.

This is a genuine OEM sourced replacement part designed for use with generators. This assembly includes a plastic brush holder, two (2) carbon brushes with a lead wires and springs attached. Carbon brushes are a commonly replaced part on power tools. Due to normal use and friction brushes will gradually wear down and will require replace...Read morement. It is advised to replace both brushes at the same type. You would need a screwdriver to complete this job. • Make sure the unit is unplugged • First remove the cover and gain access to the brush assembly • Take our old brushes and replace them with the new ones • Reassembly the cover

This fuel gauge cap is a genuine manufacturer-approved replacement part sourced directly from Briggs and Stratton. It is commonly used in portable generators to determine the amount of fuel left in the tank. This gauge is made of plastic, and it is sold individually. No tools are needed to install it. Simply discard the old gauge and replace with the new part.

This is an authentic item that is supplied directly from the original equipment manufacturer for Briggs and Stratton Generators. This kit includes one (1) female quick connect, one (1) Male quick connect, four (4) Clamps and the flexible rubber hose. This kit is used to connect the fuel lines to the fuel tank. It is recommended to install these parts in a well-ventilated area.

This is a genuine replacement part sourced from the original manufacturer for use with small engines. The special gasket is commonly used to seal the connection between the exhaust manifold and the cylinder head. This special gasket is available as an individual replacement part, please see model diagram for associative parts.

This is a genuine manufacturer-sourced part which is made for Briggs and Stratton generators. It acts as an adapter to connect the hose. Over time the part may wear out, become brittle and begin to crack eventually requiring a replacement. Make sure to check the appropriate diagrams for your model to ensure the exact location and the corr...Read moreect application. Note, one durable plastic quick connect is included. You may need pliers to perform this repair.

This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cover. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct par...Read moret. You will require a wrench when replacing this item. This part is sold individually.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton generators and pressure washers. The purpose of this component is to reduce the vibration of a working unit, unfortunately, over time it may begin to fail eventually requiring a replacement. Please make sure to refer to...Read more the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality vibe mount with a washer is sold individually.

It is an authentic item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton and Troy-Bilt equipment. This is an identical replacement for a missing or a faulty push nut that was installed on a new unit, please make sure to refer to the appropriate diagrams of your model for the correct locat...Read moreion and application of this component. Keep in mind this high-quality push nut is made of durable plastic with metal and is sold in a pack of two.