1653 - Overview

This 10-32-inch hex nut works with multiple appliances in your home as a fastener. This specific model is sold individually. Hex nuts usually have 6 even sides and together they are used with bolts and screws in order to hold items firmly together. This piece is a fastener that attaches one item to another. This part has several advantage...Read mores, the main one being that it is universal and can be used with most pieces and appliances in your home. This hex nut is an original equipment manufacturer part, meaning it is directly sourced from the manufacturer.

This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.

This chute base, also known as a discharge chute base, is sourced from the original manufacturer for use with snowblowers. It is found at the end of the discharge chute which is responsible for directing the discharge of snow, or other materials that are being thrown by the equipment. The chute base is found at the end of the discharge ch...Read moreute where it acts as a connection point between the chute and the auger housing. The chute base aids in directing the discharge to a specific place, as well as controlling how far the discharge is thrown. If the chute base becomes damaged, cracked, or worn out, it will need to be replaced. A faulty chute base will result in snow being thrown haphazardly, not being thrown far enough or not thrown at all. It can also create blockages in the equipment, leading to potentially expensive repairs. Remove the fasteners that secure the base to the equipment and pull off the old chute base. Align the new chute with the mounting bracket and secure it with the fasteners.

Sourced directly from the original manufacturer, this Bushing is used to reduce friction on your snowblower. It is made of durable white plastic, is not part of a kit or assembly, and is sold individually. This part should be replaced if it is worn or damaged, and you may experience problems operating the chute if it is malfunctioning. ...Read moreYou will need a wrench, a socket set, and pliers to complete this repair. Customers rate this repair as Medium difficulty.

This is a genuine OEM part made for Craftsman lawn tractors and mowers. Bearings are used to buffer moving parts from damage due to friction. They also stabilize directional movement. Bearings are high-wear parts and are changed regularly. This metal bearing is sold individually. Gauges, washers, rings, etc. sold separately.

This reversible skid shoe, also known as a skid runner or skid plate, is a genuine manufacturer replacement part. It is a metal shoe, measuring 5 3/4 inches by 3 1/3 inches and is designed for use in snow lowers/snow throwers. The shoe is mounted on either side of the auger housing where it allows you to adjust the height of the auger or ...Read morescraper bar to control the depth of the snow being cleared. The skid shoe can fail due to normal aging as they drag on the ground during operation, impact with hard objects, and improper installation. If the skid shoe is faulty, you will likely notice difficulties with moving through snow, setting the correct depth, and damage to the other equipment components. To replace the faulty skid shoe, first remove the bolts that secure it to the auger housing and then pull it off. Align the new shoe with the mounting holes and reinstall the bolts to hold it in place.

Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carriage bolt and is an important component to the axle assembly. This locknut has a 3/8-inch inner-diameter and is 16 threads-per-inch. To repl...Read moreace this locknut, you will need a wrench, and if there are multiple locknuts on your equipment, they may all need to be replaced.

An authentic high quality retainer that is supplied directly from original equipment manufacturer for use with Murray, Snapper and Simplicity snowblowers. This part is secured on the bottom of the chute assembly, it helps to secure it to the auger housing. It is a durable plastic item that is sold individually, please note the hardware to secure it is sold separately.

This hex nut is a fastener made from steel and is used to secure the end of a bolt in various lawn and garden equipment and machinery. It is a genuine OEM replacement part that comes in a standard size of 5/16 of an inch with 18 threads per inch. The hex nut has a hexagonal shape, which gives it greater grip and makes it easy to tighten u...Read moresing a wrench or a set of pliers. The nut also has a flange on one end, which locks the nut in place, prevents damage to the area where it is installed, and allows the load to be evenly distributed. It is important to replace your hex nut if it is loose, cracked, or corroded. If you have not yet removed the old hex nut from your equipment you will need a socket wrench to remove it. After that, you can easily install the new nut by threading it onto a bolt or screw and then tightening it with a wrench or pliers until it is tightly secured.

This Auger Drive Belt is an original part from Craftsman for use with Craftsman Snowblowers. The auger drive belt rotates the auger on the snowblower. The most common reason for replacing the drive belt is when the snowblower auger won't turn.This part is sold individually. Her is a list of tools that are needed to replace the auger drive belt are a 3/8 inch socket, 9/16 inch wrench, adjustable wrench and a clamp.

The hair pin is a silver, metal pin used to secure and lock parts in place. If broken, the part being secured will come loose and the pin should be replaced. This is an OEM part directly from the manufacturer. Most customers rated the replacement of the hair pin as an easy repair.

The deflector spring is made of metal and attaches to the deflector assembly. This spring is available as an individual replacement part. It will need replacement if it becomes stretched or broken. It is used in Husqvarna, Poulan, and Jonsered snowblowers and is an OEM from the manufacturer.