1617HC Simplicity Lawn Mower - Overview

This is a Genuine Manufacturer Sourced replacement part used on a a variety of Engines. This is a Fuel Line Connector connects the fuel line to the carburetor. This part is made out of Plastic and Metal, it is Sold Individually.

This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in length. Your machine may have a loud hissing or popping sound coming from the exhaust area if the gasket was faulty. You may also notice th...Read moree presence of black soot around the gasket or the exhaust. Your gasket needs to be replaced if it appears worn or deformed. Otherwise, your machine will experience exhaust leaks. To detach the gasket, remove the fasteners that secure it using a socket or wrench. You can detach the gasket from your machine afterwards. Please bear in mind that this replacement part is sold individually.

This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.

This Fuel Filter is a white plastic part attached within the fuel delivery system between the fuel tank and carburetor. Installation is rated as "Easy" and requires a set of pliers and a screwdriver. If broken, there may be a leak or blockage and the part should be replaced. The part may also need to be replaced according to manufacturer'...Read mores specifications, and is a manufacturer-approved part. Refer to your make, model and diagrams to ensure this part is correct.

The Seal-O Ring, also known as the gasket, is red in color, made of rubber, and is an OEM part that requires some skill to replace. This part is designed to create a seal between the carburator and manifold, to prevent air from entering. If your engine loses power, creates a hissing noise, or if the gasket appears damaged or your engine r...Read moreunning improperly it may be time to replace the part. If you run the engine and spray the outside of the carburator with soapy water, you can test whether or not the gasket is leaking by listening to the sounds produced. If the sound smooths out then you've found your leaky gasket. Damage may occur over time, especially if the part dries out, and make the part appear stretched or worn out. When making this medium-difficulty repair, make sure the new gasket is fitted properly between the carburetor and intake manifold.

This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.

This is a Genuine OEM replacement part used on variety of Lawn and Garden Equipment Engines. This part is made out of Rubber and it is sold individually. If the carburetor is leaking fuel it is recommended to replace the Bowl Gasket. Gaskets and O-rings are a common source of problems. They eventually shrink, causing fuel and air leaks that lead to poor engine performance.

This short-style engine oil filter is designed to remove harmful contaminants from the oil while maintaining proper lubrication in pressure-lubricated small engines. Built with high-efficiency filtration media and internal safety features to support consistent oil flow, it helps reduce engine wear and protect internal components. Ideal fo...Read morer routine maintenance, it supports reliable performance and helps extend engine life during regular operation.

This cotter pin is an OEM part that is 1.25 inches long, gold in color, and sold individually. Made of metal, it can have a range of applications on a variety of lawn and garden equipment. Generally, you will need to replace this part if it becomes broken due to age and wear, or if you need to remove it for making other repairs. This is...Read more an easy repair that only requires a pair of pliers to carry out. You need to bend one end around the shaft or bolt and bend the other around the back end of the bolt to complete the repair.

This Ball Bearing is an individually sold, silver/black, metal part. It reduces friction in the spindle assembly between the spindle shaft and the spindle housing. If broken due to wear/fatigue, you will hear a grinding, growling, rumbling or screeching sound, and should replace the part. Refer to your make, model and diagrams to ensure this is the right part for you.

This is a manufacturer approved starter pinion gear designed for use with lawn and garden equipment engines. This Starter pinion gear is attach to the starter clutch drive and engages the flywheel to start the engine. It is made out of Plastic and Aluminum and it is Sold Individually.