1575 - Overview

This is a genuine OEM sourced replacement part designed for use with generators. This assembly includes a plastic brush holder, two (2) carbon brushes with a lead wires and springs attached. Carbon brushes are a commonly replaced part on power tools. Due to normal use and friction brushes will gradually wear down and will require replace...Read morement. It is advised to replace both brushes at the same type. You would need a screwdriver to complete this job. • Make sure the unit is unplugged • First remove the cover and gain access to the brush assembly • Take our old brushes and replace them with the new ones • Reassembly the cover

This is a genuine replacement part sourced from the original manufacturer for use with snowthrowers and lawnmowers. The special capscrew is used with several different models of equipment, and the application of the capscrew can vary based on the model of snowthrower or lawnmower. This capscrew is available as an individual replacement part, please see model diagram for associative parts.

This centerlock nut, also known as a flange nut or hex nut flange is a manufacturer approved replacement part. It is 5/8 of an inch with 18 threads per inch. The nut is designed to secure the bolt or screw it is positioned on and prevent it from loosening during use. It has a series of ridges on the inside that allow it to grip the thread...Read mores of the bolt or screw and a flange at its base to provide a larger surface area to clamp on. Over time the lock nut may break or become stripped. Inspect all the centerlock nuts on your equipment as you may need to order more than one for your repair. To install a new nut, use your hands to thread it on and use a pair of pliers or a wrench to tighten it until it is securely held. Be careful not to overtighten the nut as this can deform the nut and wear down the threads that keep it secure. If you experience difficulties removing or tightening the nuts, use a centerlock nut tool or a cassette lockring tool instead. Note that this nut is sold individually.

This is an original Briggs & Stratton replacement part. The screw is designed by the manufacturer for use in generators. This part is made of metal, and is generally used in securing the bearing cover. Please be aware that there are different screws used in the machine. Refer to the parts diagram to be sure of ordering the correct par...Read moret. You will require a wrench when replacing this item. This part is sold individually.

Used to hold a shaft with a mating part, such as a gear, this Woodruff Key is sourced directly from the original manufacturer, is made of metal, is grey, and is sold individually, not as part of a kit or assembly. When this part becomes broken or damaged, it should be replaced. You may notice the mating shaft or gear will no longer rota...Read morete together if the part is malfunctioning. Customers rated this repair as Easy.

This O-ring is an OEM component of the nozzle insert on various Karcher pressure washers. An O-ring is a flexible ring used as a pressure seal between rigid parts. It is a simple yet essential part for machine performance. This ring is sold individually.

The manufacturer certified M8 Flange Nut is an 8mm silver, serrated, metal part. It can be installed using a wrench or socket, and is used to secure parts in place and secure the load. If broken or damaged, the nut and part may be loose and it should be replaced. Check your make, model and diagram to ensure you are choosing the correct part.

This item is available as an individual replacement part. The outlet is made out of metal and plastic. It may require a wrench during installation. This item will need to be replaced if it breaks. It is a replacement part directly sourced from the manufacturer for use in generators made by Briggs & Stratton and Snapper.

Lockwasher split 3/8

Length: 8' Gauge: 18 Wires: 2 Type: Bare Wire This cord is a genuine DeWalt replacement part. This cord is compatible with the list of models below. This part is made for double insulated tools It is a two wire cord with two prongs and does not need a ground wire. The cord is sold individually. Installation of this part requires the...Read more new cord wires to go correctly into wire terminals also routing the cord and wires in the right path can help avoid pinching when the tool case (Plate) is put back into place.

This is a genuine OEM replacement part, it is sold individually. This part is used to keep the brush tight against the armature so the tool will work properly. Over time when the brushes wear down and heat is created, the spring may lose its tension and will have to be replaced.

This is a genuine OEM supplied replacement part designed for use with drills/drivers. This screw helps to secure the chuck to the unit. This is a reverse thread, oval-head Torx screw, made out of metal and it is sold individually. Requires a Torx screwdriver to install or remove this screw.