1540 - Overview

This nut is a manufacturer-approved replacement part for various lawn and garden equipment. It is sold individually, not as part of a kit or assembly. Also referred to as a Lock Nut, it is resistant to loosening when threaded on a bolt. It has a variety of applications and is used in multiple locations on most models. Please refer to your...Read more owners manual to determine the exact location. While made of durable metal, the ends can round off from improper use of a wrench or socket. Depending on the location, this part may also become worn through regular use of your machine. It should be replaced when visibly cracked, worn or damaged. To complete this repair, you will need a wrench or socket, and a torque wrench. Ensure you torque the bolt according to the manufacturer recommendations. Customers rate this repair as Easy.

This roll pin is a genuine OEM part that is designed for use with various makes and models of snowblowers and lawn tractor snowblower attachments. Made of metal and sold as an individual part, this pin features a 0.25-inch diameter and 1.75-inch length. This pin is hollow and features a split lengthwise down the middle to allow it to fit ...Read morewithin tighter spaces and reduce the movement between two parts, such as the shaft or axle. If your snowblower is not performing well or has seen a decrease in power, check to make sure the roll pin is not damaged. To remove and install a new roll pin, you will need a hammer and a punch, and will simply need to punch out the old pin and punch in the new one.

This Washer-Lock 5/16 is a silver, metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter, it is used to prevent the nut from backing off and becoming loose on the pulley shaft, and is attached to the drive belt pulley assembly. You will know if you nee...Read mored this because your owners manual will specify it, or the model number of your machine will correspond with this part. If the part is broken due to fatigue, the shafts will free spin when they should be locked together, and must be replaced.

This item is an authentic OEM sourced O-ring kit that replaces worn or damaged O-rings for the gun, hose and wand.Unfortunately, over time o-rings will wear out and they may begin to crack eventually requiring replacements. Refer to the appropriate diagrams for your model to ensure the correct replacement procedure. A screwdriver and a wr...Read moreench set might be needed to take apart and reassemble the equipment. Note, this kit is sold as an individual item.

This replacement part is used on the base of various models of pressure washers to reduce vibration from the pump. This Grommet has an O.D. of 1 inch, is not part of a kit or assembly, is sold individually, and is made of durable black rubber. This part is known to wear with regular use of your machine, it should be replaced if you noti...Read moreced more vibrations than normal within the unit. Customers rate this repair as Easy.

This is an authentic OEM part for use with Craftsman Pressure Washers. The quick connector also is known as the wand connects to the spray gun handle and houses the nozzle that directs the spray stream. The most common reason for replacing the wand is if it is leaking or damaged. This part is sold individually. The tool that you will need to replace the wand is Silicone grease (optional).

This bottle of oil can be used in over 150 different types of machinery. It is most commonly used for pressure washers and generators from manufacturers such as Briggs and Stratton and Troy-Bilt. This detergent oil is warranty approved and specially compounded for warm weather use. Please note: it is important to avoid over filling your engine with oil.

This authentic part is supplied by the original manufacturer for use with Ariens lawn and garden equipment. The flange bushing helps to provide a tight seal between connected parts while allowing for movement with minimum friction. Over time it may wear out, get damaged or lost eventually requiring a replacement. This high-quality flange ...Read morebushing is made of durable material and is sold individually. A screwdriver, pliers and a wrench set might be needed to perform this repair. Make sure to refer to the appropriate diagrams for your model to ensure the proper replacement procedure.

This ash catcher handle is a replacement grip component designed to allow safe, controlled removal of an ash container. It provides durability and heat resistance and is commonly replaced when bent, loose, or damaged through regular use.

This is an authentic OEM part. This key is made of molded plastic and metal and is designed for use with Ariens snowblowers and snow tractors. It is used to start the machine and functions as a safety feature to prevent unauthorized use. This item is sold individually.