152S Husqvarna Lawn Tractor - Overview

This is a genuine Craftsman part for use with Lawn Mowers. The zone control cable stops the engine when you let go of the handle. This part is sold individually. The most common reason for replacing the control cable is if it is broken, causing the brake to not release even when the lever is pressed. The tool that you will need to replace the zone control cable is pliers.

This Handle Bolt is sourced directly from the original equipment manufacturer for use in various lawn and garden equipment. It is used to secure the upper and lower handles together and is tightened by a knob on the other end. It is made of metal, is black, and is sold individually, not as part of a kit or assembly. This part will need ...Read moreto be replaced when it is worn or damaged and can no longer secure the arms together. No tools are needed to complete this repair. Customers rated this repair as Easy.

It is a genuine OEM supplied item which is made for walk-behind lawn mowers. This is a high-quality replacement for a missing or a damaged pinion gear that helps to drive the mower's wheel. Unfortunately, over time due to friction, the teeth on the gear may wear out. If this happens it will no longer engage the wheel and the mower will no...Read moret move. To ensure the exact location and the correct installation of the new part, refer to the diagrams of your specific model. Note, one durable metal pinion is included. You will need a wrench set and pliers to remove the old pinion and secure the new one.

Made of high-quality metal, this hex flange locknut is designed for use with various lawn mowers and ride-on mower/tractor models and is sold individually. This locknut attaches to the end of the carriage bolt and is an important component to the axle assembly. This locknut has a 3/8-inch inner-diameter and is 16 threads-per-inch. To repl...Read moreace this locknut, you will need a wrench, and if there are multiple locknuts on your equipment, they may all need to be replaced.

The E-Ring 7/16 is a 7/16-inch silver, metal part which can be attached to various locations on a variety of equipment to snap into grooves and secure parts into place. This part will require pliers to install. If broken, damaged or worn, there may be a problem with the part it is securing and the part should be replaced. Refer to your make, model and diagrams to check if this is the right part.

This part has been sourced from the original manufacturer and is intended to be used with walk-behind lawnmowers from Husqvarna, Poulan, Weed Eater, and Jonsered. The metal pawl is used to secure the pinion to the transmission axle to allow the two parts to rotate in unison. This drive pawl is priced as a single item, please note two may be needed.

This is a genuine replacement part sourced from the original manufacturer for use with walk behind mowers made by Husqvarna and Poulan. This part helps stabilize the torue shaft assembly front. It is recommended to review your models diagram to verify the parts compatibility. This part is sold individually and made of durable material.

This washer is not part of a kit or assembly. It is sold individually. With an O.D. of 1 inch, this OEM replacement part is made of dark grey metal and is used to provide a tight seal between the mower blade and the blade bolt/screw. This part should be replaced if you notice any visible wear, warping, or damage. You will need a wrench or socket set to complete this repair. Customers rate this repair as Easy.

This is a genuine part that is supplied by the original manufacturer for use with Craftsman lawn mowers. The drive cable assembly connects the handle drive control to the transmission which enables you to push the mower forward. This part is sold individually and is made of hard plastic and metal wire. You will need a screwdriver and need...Read morele nose pliers to aid you in this repair. Let the engine cool before you begin installing.

This is an authentic Craftsman replacement part, sourced from the original manufacturer for use with walk-behind lawnmowers. The special lever connects to the shaft assembly and is used to adjust the height of the front end of the mower's deck. This item is available as an individual replacement part, please note two levers are required.

This replacement grill is an authentic OEM sourced item that is specially designed for Husqvarna lawn mowers. It is secured over the wheel for aesthetic purpose as well as to provide protection from dust and other debris. It is made of durable plastic and is sold individually. Replacing this hubcap is a very simple task that does not require any tools. Refer to the owner's manual for the correct application.