My Orders
14V Cub Cadet Lawn Mower - Overview
Models starting with 14V
Click on the best match to narrow your results.
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$9.69
In Stock
Engine Oil Seal
Part #795387
This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty as Medium.
This part provides a seal around the crank shaft and engine block. When installing onto the engine block around the crank shaf...Read moret, use something that makes contact around the entire seal, like a large socket or pipe, and tap into place evenly, ensuring that the housing is clean and dry. If the part is broken, likely due to fatigue, there will be leaking oil, and this part should be replaced using the model number on the original part to confirm it is the right fit for your model.
Read less
$30.09
In Stock
Engine Cylinder Head Gasket
Part #693997
This is a replacement cylinder head gasket for your small engine. The gasket is approximately 5 inches in length and 5 inches in width at its longest and widest points. The gasket creates a seal, and the seal allows combustion to occur, making your engine run at peak performance. If the gasket is damaged or coming apart, you may notice a ...Read moredecrease in the power and performance of your engine. When you remove the old gasket, be sure that the surface you are attaching the new one to is completely clean, so the seal will be effective. This part is sold individually and it is a genuine OEM part.
Read less
$6.40
In Stock
Lawn Mower Self-Tapping Screw
Part #710-04484
$17.25
In Stock
Engine Oil Filter
Part #696854
This genuine OEM oil filter helps to remove harmful contaminants from engine oil. It is designed for a variety of Engines. It is sold Individually. This part maintains optimum performance of your engine in accordance with applicable EPA emissions regulations. It is recommended to replace an Oil Filter at least once a season.
$6.40
In Stock
Carriage Bolt 5/16-18 x 3/4" Lg.
Part #710-0451
This carriage bolt measures 5/16-18 x .75 and fastens two parts in your machine together. It has a round domed head and a square underside so the bolt does not rotate once it has been secured into place. If it has signs of deformation or wear, you will need to replace it. To unthread this bolt, you need an adjustable wrench to loosen the ...Read morenut found on the end of the bolt. You may need to apply a lubricating oil to the bolt if it is stuck. You may need to clamp down on the head of the bolt with pliers while continuing to turn the nut counterclockwise. You can then slide the carriage bolt out of its hole or tap it gently with a hammer. This bolt is a standalone product and the nut is not included. This bolt was sourced directly from its manufacturer.
Read less
$6.40
In Stock
Lawn Mower Hex Washer Head Screw
Part #710-0599
This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.
Read less
$53.18
In Stock
Crankcase Gasket With Bolts
Part #594195
This genuine crankcase gasket is used on small lawn and garden engines. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time this gasket will deteriorate and will need to be replaced. It is made out of composite material and it is sold individually. To complete this repair you will need a wrench. Includes ...Read moreone (1) gasket and ten (10) bolts. This will need to be tightened with torque to 300 inch pounds.
Read less
$6.40
In Stock
Nut-flglk 5/16-18
Part #712-04063
This nut is a manufacturer-approved replacement part for various lawn and garden equipment. It is sold individually, not as part of a kit or assembly. Also referred to as a Lock Nut, it is resistant to loosening when threaded on a bolt. It has a variety of applications and is used in multiple locations on most models. Please refer to your...Read more owners manual to determine the exact location.
While made of durable metal, the ends can round off from improper use of a wrench or socket. Depending on the location, this part may also become worn through regular use of your machine. It should be replaced when visibly cracked, worn or damaged. To complete this repair, you will need a wrench or socket, and a torque wrench. Ensure you torque the bolt according to the manufacturer recommendations.
Customers rate this repair as Easy.
Read less
$6.40
On Order
Seal-o Ring
Part #691917
The Seal-O Ring, also known as the gasket, is red in color, made of rubber, and is an OEM part that requires some skill to replace. This part is designed to create a seal between the carburator and manifold, to prevent air from entering. If your engine loses power, creates a hissing noise, or if the gasket appears damaged or your engine r...Read moreunning improperly it may be time to replace the part.
If you run the engine and spray the outside of the carburator with soapy water, you can test whether or not the gasket is leaking by listening to the sounds produced. If the sound smooths out then you've found your leaky gasket. Damage may occur over time, especially if the part dries out, and make the part appear stretched or worn out.
When making this medium-difficulty repair, make sure the new gasket is fitted properly between the carburetor and intake manifold.
Read less
$6.40
In Stock
Lawn Mower Flanged Lock Nut
Part #712-04065
Designed for use in various models of lawn and garden equipment, this part is not sold as part of a kit or assembly. It is made of metal, is gold in color, and is sold individually. This part may also be called a Flange Lock. This nut is designed to lock in place, preventing vibrations and other parts coming loose.
This nut may be locate...Read mored in multiple locations on your machine, refer to your owners manual to determine if this is the correct part. You will need a wrench or socket set and a torque wrench to complete this repair. You should only torque the nut to the manufacturer recommendation, no tighter.
You will need to replace this part when it is worn or damaged. While this part can wear through regular use, it is most commonly damaged through improper use of a wrench or socket.
Customers describe this repair as Easy.
Read less
$6.40
In Stock
Gasket-exhaust
Part #690970
This is a genuine OEM sourced replacement exhaust gasket. It is specially made for use with Briggs and Stratton engines commonly used on Toro lawn and garden equipment. Its purpose is to provide an air-tight seal between the carburetor and the exhaust tube. Over time this gasket will deteriorate requiring replacement. Please note, this co...Read moremposite gasket is sold individually. To replace this part you will need a wrench.
Read less
$16.91
In Stock
Lawn Mower Steering Pinion Gear
Part #717-1554
This steering gear is an original part from Craftsman for lawn tractors. This piece is part of the tractors steering mechanism. This steering gear maneuvers the steering sector gear to move the lawn tractor wheels right or left. You will need a socket set to replace this part. This steering gear is made of metal and sold individually.
Common Symptoms of models starting with 14V
How this model fails, and the parts that fix it.
Watch our pros, then fix it yourself.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
governor not working
17 of 29 people
found this instruction helpful.
Had to pull the engine off the rider mower. Drained the oil took shield off the flywheel. Set it upside down on a 5 gal bucket. Took a 7/16 hand wrench to remove governor lever from bottom of engine. Left it in its location. Pulled 10 1/2 " bolts. Split engine case. Found the old governor had broke into pieces. Had to use a magnet t
... Read more
o remove all the pieces. Removed the small clip and removed gear. Lubed shaft slid new on put new clip on. Lined governor weights with center piece tapped it in place very lightly. Cleaned gasket flanges pulled the shaft seal. Used the old seal as a seal driver. When putting the cover back on make sure the seal dont roll out. Take a mini screwdriver and tuck it in around shaft. Put bolts back in and tighten like instructions
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!