144411-0147-99 Briggs and Stratton Engine - Overview

The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "Medium" difficulty and requires a screw driver, wrench set and seal puller. A broken seal will cause a leak, and the part must be replaced. R...Read moreefer to your make, model and diagram to ensure you're choosing the right part. This part comes in black and gray.

This starter pulley, also known as a recoil starter pulley, is sourced from the original manufacturer for use in outdoor power equipment. It includes the starter rope and plastic spool to hold the rope. Over time the rope may fray, tear, or the plastic spool may break. A faulty starter pulley will lead to difficulties pulling and retracti...Read moreng the rope, and starting the equipment. To replace the faulty parts, ensure the equipment is off and disconnected from power. Remove the starter housing/cover and remove the old spool and rope. Wind the rope around the new spool and tie a knot to secure it in place. Place the new spool and rope inside the starter mechanism and feed the end of the rope out of the hole in the housing. Reattach the starter cover to complete the repair.

This rewind starter spring or as it is also known, recoil spring, rewinds the pull robe back into the starter housing of your engine. The spring is made of metal, silver colored, and sold individually. Over time, you may notice that you are having trouble retracting your pull cord, which could be a symptom of the rewind starter spring f...Read moreailing due to fatigue or wear. Replacing this part is a repair our customers found easy. Locate and replace the start spring inside the starter housing; no special tools are required for this job.

This starter clutch is an authentic OEM replacement part used in small outdoor power engines. Each package includes one clutch and one ball bearing. The starter clutch allows the engine to start by engaging the crankshaft to spin the engine and initiate combustion. Once the engine starts the clutch disengages to prevent over spinning. Ove...Read morer time the clutch may fail due to worn-down bearings, or damage to the clutch body, resulting in hard starting or failure to start. To replace it, first, disconnect the spark plug for safety. Then, remove the engine cover to access the starter clutch. Remove the clutch from the crankshaft, and thoroughly clean the mounting shaft. Install the new clutch by screwing it onto the crankshaft, then reassemble the engine cover and reconnect the spark plug.

This is a high-quality manufacturer-sourced part which is made for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It helps to distribute the pressure evenly and provide a tight seal for the breather. Over time it may become brittle and begin to crack eventually requiring a replacement. For the proper...Read more application please refer to the appropriate diagrams of your model. This high-quality part is made of durable composite material and is sold individually. You will need a screwdriver and a wrench set to remove and reattach the breather.

This air cleaner element is supplied from original manufacturer. It is specially designed for use with Briggs and Stratton engines used on lawn and garden equipment. It is used to filter out dust from entering the carburetor and the engine. This filter element is made out of foam material and it is sold individually. Please note, the air ...Read morecleaner cartridge is sold separately. Replacing this filter is a simple task that does not require any tools. • Unscrew the cover knob • Remove the cover • Remove old element • Secure the new element in place • Reassemble and test the unit

This replacement rewind starter is an authentic high quality item designed for use with Briggs and Stratton engines commonly utilized on Toro lawn and garden equipment. This is the complete starter assembly that allows user to easily pull-start the engine. It includes a plastic housing, starter pulley, starter spring, pull rope with a gri...Read morep and the hardware to secure this assembly. To complete this repair you will need a wrench.

This is an authentic OEM component from Briggs & Stratton. The magneto armature screw is compatible with many lawn and garden engines. The hardened metal screw helps to mount the magneto armature. A wrench is required for the removal and installation. The magneto armature screw is sold individually. It is recommended to refer to engine manual and diagrams for further instruction.

The clutch ball allows the center part of the ratchet to turn backwards freely but catch when turned forward in your engine. This is an OEM part that is made of metal, and it is silver in color. This part will break due to fatigue and wear, and you will know if the part needs replacing if it is no longer able to swing outward to catch t...Read morehe outside of the clutch to start the engine. If this occurs, it is time to replace the clutch ball, which our customers found to be a challenging repair.

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in engines, lawn tractors, and snow throwers from Briggs & Stratton and Toro. This part is made of metal, and is generally used to secure the cylinder shield. Please be aware that there are different screws used in the machine. Ref...Read moreer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

This genuine item is supplied by the original equipment manufacturer for use with Briggs & Stratton engines and Toro snowthrowers and lawn tractors. The crankcase gasket attaches the crankcase cover to the cylinder assembly and helps to seal them together. You may need a wrench when replacing this part. Over time this part may break and w...Read moreill need to be replaced. This item is made out of a thin material and is priced individually.

It is a manufacturer supplied replacement part that is designed for use with Briggs and Stratton engines. This carburetor intake gasket which provides an air tight seal for the breather assembly. Over time gaskets tend to deteriorate and crack eventually needing a replacement. It is made from durable composite material and it is sold individually.