1443-0 Briggs and Stratton Pressure Washer - Overview

This item is an authentic OEM sourced O-ring kit that replaces worn or damaged O-rings for the gun, hose and wand.Unfortunately, over time o-rings will wear out and they may begin to crack eventually requiring replacements. Refer to the appropriate diagrams for your model to ensure the correct replacement procedure. A screwdriver and a wr...Read moreench set might be needed to take apart and reassemble the equipment. Note, this kit is sold as an individual item.

This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment, and can be used in a lot of different equipment, so be sure to consult your owners manual or check your part number to ensure this fits yo...Read moreur model. Over time the washer may become damaged; watch for cupping from over-tightening as a leading cause. This is a very easy part to repair and does not require any tools.

This is a genuine replacement part that has been sourced from the original manufacturer to be used with generators and pressure washers from Briggs & Stratton and Snapper. The vibration mount fits between the engine and the frame assembly and is used to reduce vibration between the motor and frame. This item is sold as an individual replacement part.

This replacement part is used on the base of various models of pressure washers to reduce vibration from the pump. This Grommet has an O.D. of 1 inch, is not part of a kit or assembly, is sold individually, and is made of durable black rubber. This part is known to wear with regular use of your machine, it should be replaced if you noti...Read moreced more vibrations than normal within the unit. Customers rate this repair as Easy.

This is an authentic OEM part for use with Craftsman Pressure Washers. The quick connector also is known as the wand connects to the spray gun handle and houses the nozzle that directs the spray stream. The most common reason for replacing the wand is if it is leaking or damaged. This part is sold individually. The tool that you will need to replace the wand is Silicone grease (optional).

This bottle of oil can be used in over 150 different types of machinery. It is most commonly used for pressure washers and generators from manufacturers such as Briggs and Stratton and Troy-Bilt. This detergent oil is warranty approved and specially compounded for warm weather use. Please note: it is important to avoid over filling your engine with oil.

The authentic 10" Wheel Assembly (Wheel, 10" Diameter) is a 10-inch black, plastic-and-ubber wheel. It allows easy moving of the generator. Installation requires pliers and is rated as "Easy". If your tire is flat, then it should be replaced. Refer to your make, model and diagram to ensure this is the right part.

This is an authentic Briggs and Stratton replacement part manufactured for use with pressure washers. This gasket forms a seal between the pump head and inlet plate spacer. It is recommended to replace pressure washer gaskets when servicing the pump to ensure a proper seal when reassembling the pump. This head gasket is available as an individual replacement part.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton generators and pressure washers. The purpose of this component is to reduce the vibration of a working unit, unfortunately, over time it may begin to fail eventually requiring a replacement. Please make sure to refer to...Read more the appropriate diagrams of your model for the correct location and application of this part. Keep in mind this high-quality vibe mount with a washer is sold individually.

The manufacturer certified M8 Flange Nut is an 8mm silver, serrated, metal part. It can be installed using a wrench or socket, and is used to secure parts in place and secure the load. If broken or damaged, the nut and part may be loose and it should be replaced. Check your make, model and diagram to ensure you are choosing the correct part.

This is an authentic component is sourced directly from the original equipment manufacturer. It is the part that is specially made for use with Briggs and Stratton and Snapper pressure washers. The purpose of this o-ring is to provide a tight seal between connected components. Unfortunately, over time it may wear out and begin to crack ev...Read moreentually requiring a replacement. Please make sure to check the owners manual and the diagrams of your model for the correct installation of this part. This high-quality o-ring is made of durable rubber and is sold individually.