This microwave fuse is just over an inch in length. It has a white ceramic center, and metal on either end. This is a twenty amp 250-volt fuse, and is used to power your microwave. If your microwave will not heat properly, will not turn on, or the touch pad becomes unresponsive, there could be a faulty fuse which should be replaced. Remem...Read moreber, since this part contains an electrical charge, before you replace the fuse from your microwave, make sure that the power is disconnected from the unit. This part is sold individually.
NOTE: Make sure your microwave is unplugged, and your capacitor is discharged before you begin this repair. A capacitor stores large amounts of electricity even after your microwave is unplugged.
This is a heat-resistant adhesive for your appliance. The heat resistance allows you to stick parts such as grate feet, gaskets, and felt seals in hot areas, such as a cooktop, without compromising the integrity of the adhesive. It is white in color, and the tube is approximately 7.5 inches long.
This hex nut is an authentic Whirlpool part that is sourced directly from the original equipment manufacturer, and will fit a variety of appliances including ovens, microwaves, refrigerators, air conditioners, and dishwashers. It is a metal part with a threaded hole to fasten parts in the appliance together. It is common for this part to ...Read morewear out; it is recommended to order a spare. To replace this part the tools needed are a nut driver or wrench. This nut features a built-in external tooth lock washer, which is used to help keep the nut in place.
This two speed split phase washing machine motor performs 1725 revolutions per minute in one speed and 1140 revolutions per minute in the other speed. This motor runs at 1/2 horsepower and it carries 8.0 amps. It's a good idea to change your washer's belts at the same time as you replace this motor, as they may have become worn as well.
This spark plug cover is supplied directly from the original equipment manufacturer. The rubber and metal component is often used in snowthrower engines, and is sold individually. The spark plug cover is fitted over the spark plug wire connection, providing protection. A screwdriver and pliers may be required for the removal and replacement.
This is a genuine Tecumseh part for use with Lawn and Garden Equipment Engines. The fuel line supplies gas from the tank to the carburetor. The most common reason for replacing the fuel line is when the engine is leaking fuel. This part is sold individually. The tools that you will need to replace the fuel line is a 5/16 inch socket or nut driver and pliers.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
microwave oven blew fuse
27 of 43 peoplefound this instruction helpful.
tad from tamarack, MN
Really Easy
Less than 15 mins
Pliers, Screw drivers
First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With th
... Read moree help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix .
Read less
Was this helpful?
Thank you for voting!
Motor Froze
22 of 28 peoplefound this instruction helpful.
Matt from Oxford, GA
A Bit Difficult
1- 2 hours
Nutdriver, Pliers, Screw drivers
Make sure to release the springs and pulleys before you try to tackle the bolts that hold the motor base to the bottom of the washer. Mine were a bit rusty and took some force to break loose. Also it's a good idea to take pictures of how everything sits before you disassemble as the pictures in the repair kit are not very clear. Oth
... Read moreer than that it was pretty straight forward. Wiring was a breeze. . . . Good luck
Read less
Was this helpful?
Thank you for voting!
the motor burnt out
17 of 24 peoplefound this instruction helpful.
walter from watertown, WI
Really Easy
1- 2 hours
Socket set
took washer into the garage, removed front cover & disconnected the wiring. Then i removed the motor assembly. Piece of cake to finish job.