This washer/dryer lid or door switch kit serves as a critical safety component, designed to prevent the appliance from operating when the lid or door is open. It ensures that the washer does not fill or spin and the dryer does not start unless the door is securely closed, helping to avoid water spills and potential safety hazards. The kit...Read more includes all necessary components for installation and is compatible with a wide range of top-loading washers and front-loading dryers. Installation typically involves disconnecting power, accessing the control panel or door area, and replacing the switch using standard tools. The switch is compact and designed to fit seamlessly within the appliance’s housing, with dimensions approximately 2.5 inches in length, 1 inch in width, and 1 inch in height. It features a neutral color finish that blends with most appliance interiors.
This is a delta frame surface unit, also known as coil element, for a stove, range, or oven. It is a 6-inch surface burner with a reinforced delta frame that carries 1250 watts and 240 volts. The burner has four turns and is compatible with many electric ranges. The center medallion is black in color. The burner provides heat to your cook...Read moreing area to cook your food items. If your burner is not heating properly, you may need to replace it. Be sure to disconnect power to the appliance before completing this repair.
This 10-32-inch hex nut works with multiple appliances in your home as a fastener. This specific model is sold individually. Hex nuts usually have 6 even sides and together they are used with bolts and screws in order to hold items firmly together. This piece is a fastener that attaches one item to another. This part has several advantage...Read mores, the main one being that it is universal and can be used with most pieces and appliances in your home. This hex nut is an original equipment manufacturer part, meaning it is directly sourced from the manufacturer.
This Washer-Lock 5/16 is a silver metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter it is used to prevent the nut from backing off and becoming loose on the pulley shaft and is attached to the drive belt pulley assembly. You will know if you need t...Read morehis because your owners manual will specify it or the model number of your machine will correspond with this part. If the part is broken due to fatigue the shafts will free spin when they should be locked together and must be replaced.
The Adjustable Gib (Keyway) is a gray metal 2 inch individually sold part rated as easy to install by consumers. It locks two shafts together so they can rotate. You will know if you need to replace this part if the shaft is freely spinning and will not spin with the drive shaft. You can see this happening when the shaft is turning or you...Read more can turn the shaft by hand to see if the two parts connect. The part is attached between the two shafts.
The air valve attaches to the wheel and is made of a durable material. This is a genuine MTD, Ryobi, Yard Machines, Bolens, Troy-Bilt, and Yard Man part sourced directly from the manufacturer for use in chippers, shredders, cultivators, edgers, lawn tractors, snowblowers, and trimmers. Keep in mind that this part is sold individually. Whe...Read moren replacing this item a set of pliers might be required during the installation process. It might wear out over time and will need replacing.
This OEM Hub Cap, or Dust Cap, is a 2-inch, silver, steel part, sold individually. It requires a Rubber Mallet to install and its installation is rated as Easy by our customers.
This part attaches inside the wheel on the hub, and is used to keep dirt out of the hub. It must be replaced when damaged or missing (if it is damaged it will b...Read moree out of round, and will not fit). Check your model number to ensure you are purchasing the correct part.
This grease seal, also known as an oil seal or a shaft seal, in your log splitter or chipper shredder serves as a protective barrier. It keeps lubrication inside the bearings and stops dirt from entering them. It is commonly located in the wheel hubs or axle assemblies of your machine. A broken grease seal leads to contaminated bearings. ...Read moreYour machine will then undertake more friction and can overheat, reducing its performance. You will need a seal puller or a flathead screwdriver to pry a grease seal out of your machine. When installing the new grease seal, apply a thin layer of lubricant to its inner surface before pressing it into its housing. Please be informed that this OEM-certified component is sold individually.
This OEM replacement washer is often used on several different types of lawn and garden equipment but can also be used on compatible home appliances. It is made of metal meaning it is vulnerable to corrosion and will produce more noise from your lawn equipment or appliance if it has broken. Its main purpose is to reduce rattling and noise...Read more or to better secure and evenly distribute pressure between two different parts. This washer has a .38-inch inner diameter .87-inch outer diameter and .09-inch thickness and is sold individually.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lid closes, switch wouldn't turn on machine.
31 of 47 peoplefound this instruction helpful.
Kenneth from Wilmington, IL
Easy
1- 2 hours
Nutdriver, Screw drivers, Socket set
Used toothpick for a year to push switch acctuator far enough to engage switch. Broke my foot and found time to order part thru PartSelect. Went from cast to boot and received part 2 days after ordered. Had difficulty with foot and getting to switch. Went back into PartSelect and figured out how to dis-assemmble panels thru the diagrams.
... Read moreTime on my job doesn't, just that their service and expertise that is available to everyone is there to use. Broken bones or not, I will always get my parts and advice from PartSelect. Thanks to PartSelect.
Read less
Was this helpful?
Thank you for voting!
Washer would fill up, wash, then stop
22 of 31 peoplefound this instruction helpful.
Glen from Plano, TX
A Bit Difficult
30 - 60 mins
Screw drivers
I deduced the lid switch was the problem.
I removed the two screws holding the control panel on. Pulled the control panel back. Disconnected the ground wire of the lid switch. removed the two top clamps that hold the panel to the top of the machine. Pulled back the casing (outside of the washer) and placed
... Read moreit on it's side on the floor. Here I could reach the switch. Removed old, installed new and reversed the process.
The part that gave me the biggest problem was setting the casing back on to the frame. You have to slide the front part in at the bottome, then lean back the rest of it.
Read less
Was this helpful?
Thank you for voting!
One day, I found my dryer continued running after I opened the door. And next day, it stopped working at all. I thought it was time to buy a new one, since my dryer had been used for more than 15 years. But I was curious to know what went wrong, and recalled my friend told me he repaired the door
17 of 21 peoplefound this instruction helpful.
Xiaobin from Cordova, TN
Really Easy
Less than 15 mins
Screw drivers, Wrench set
My daughter found the video on youtube, which showed step by step repairing procedures. I just followed it and fixed my dryer in 15 min.