Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "M...
This item is an authentic OEM replacement part that is intended to be used with small engines from Briggs & Stratton. The breather tube is used to guide the direction of excess gasses and fluid that e...
This Fuel Filter is a white plastic part attached within the fuel delivery system between the fuel tank and carburetor. Installation is rated as "Easy" and requires a set of pliers and a screwdriver. ...
The Seal-O Ring, also known as the gasket, is red in color, made of rubber, and is an OEM part that requires some skill to replace. This part is designed to create a seal between the carburator and ma...
This manufacturer-certified Ignition Key comes in black/silver and is used in the ignition slot to turn on the engine. If your key becomes damaged or lost (which these small keys easily are), this pa...
This air cleaner cover knob is used to fasten the air filter cover securely in place on small engines. Designed for easy hand-tightening, it helps keep the air filter sealed to prevent dust and debris...
It is a genuine item that is supplied by the original equipment manufacturer for use with Briggs and Stratton engines that are commonly installed on Toro lawn and garden equipment. The cap attaches on...
This is an authentic OEM sourced replacement part that is intended to be used with lawnmower engines and outboard motors from Briggs & Stratton and Toro. The metal screw is used to secure the rocker c...
This genuine part is sourced directly from the original equipment manufacturer. It is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The p...
This manufacturer-certified Gasket-Intake, more commonly known as the Intake Gasket, is a gray, 3 x 2 inch, individually sold part which can be installed using a Wrench or Socket and a torque wrench. ...
This authentic manufacturer sourced replacement part is designed for use with lawn and garden engines. The starter motor provides an initial motion, engage the flywheel to start the engine. This start...
This part is an OEM from Briggs & Stratton. The push rod guide is compatible with many lawn tractor engines. The metal and plastic item is fitted in the cylinder head assembly, securing the push rods....
$14.95
Special Order
Questions And Answers for 13AC26JD093
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Richard
May 17, 2023
Gasoline fills cylinder when turned off and will not turn over until gas is drained through spark plug hole
For model number 13AC26JD093
Hi Richard, Thank you for writing. Sounds like there is debris stuck in the needle valve inside the carburetor. This will allow fuel to flow into the engine causing it to hydro lock until you remove the fuel from the cylinder. You will have to remove the carburetor and remove the fuel bowl then the needle valve to clean it out. I hope this helps and good luck with your repair.
Did this question help you?
Thank you for voting!
Raul
April 13, 2023
10inch
For model number 13AC26JD093
Hi Raul, Thank you for writing. This Hex Flange Bearing is approximately 1" in diameter. We hope this helps!
Did this question help you?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Removed head. Replaced both rocker arms, intake pus rod, push rod guide exhaust and head gaskets. Torqued head in 3 stages to 216 in/lbs. gapped intake to .004 and exhaust to .006 at TDC
Added oil and gas. Now running great
If you need to replace push rods use steel (exhaust) they are the same length The engine
... Read morewas a Briggs & Stratton 217802 0113 E10604 (2006 year date code) I used the following 796189 gasket 272475S gasket 697494 push rod 690822 push rod guide 691751 rocker arms
First I opened the top of the mower to expose the housing cover. Secondly I removed the four housing bolts to remove the housing cover from the mower. Next I removed the tube breather and installed the new tube breather and replaced the housing cover with the four bolts previously removed and closed the top of the mower. I filled the mow
... Read moreer with gas to check for leaks which weren't any leaks. I proceeded to mow the lawn with ease.
