13A-264G100 Cub Cadet Lawn Mower - Overview

This carriage bolt measures 5/16-18 x .75 and fastens two parts in your machine together. It has a round domed head and a square underside so the bolt does not rotate once it has been secured into place. If it has signs of deformation or wear, you will need to replace it. To unthread this bolt, you need an adjustable wrench to loosen the ...Read morenut found on the end of the bolt. You may need to apply a lubricating oil to the bolt if it is stuck. You may need to clamp down on the head of the bolt with pliers while continuing to turn the nut counterclockwise. You can then slide the carriage bolt out of its hole or tap it gently with a hammer. This bolt is a standalone product and the nut is not included. This bolt was sourced directly from its manufacturer.

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

Hard starting or an engine that suddenly stops may point to a damaged magneto armature. This ignition coil turns magnetic energy from the spinning flywheel into the electrical pulse that fires the spark plug. First try a known-good spark plug and inspect the safety switches, grounding wire, terminals, and flywheel magnet. Confirm fit from...Read more the full engine identification numbers, since similar coils may mount differently. Work only with the engine off and cool. Disconnect the battery and spark plug lead before removing covers. During installation, use the air gap listed in the service manual and tighten the mounting screws evenly. Keep hands clear of the flywheel and use an insulated tester to check for spark.

This is a manufacturer approved starter pinion gear designed for use with lawn and garden equipment engines. This Starter pinion gear is attach to the starter clutch drive and engages the flywheel to start the engine. It is made out of Plastic and Aluminum and it is Sold Individually.

The hex bolt attaches to the washer and the square key. This part is an OEM from Craftsman for use in snowblowers and lawn mowers. It is available as an individual replacement part and is made of metal. If this item becomes broken or stripped it will need to be replaced and may require a socket set during the installation.

This genuine part is sourced directly from the original equipment manufacturer. It is specially designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. The purpose of this hose is to transfer vacuum from the engine. Unfortunately, over time the material may wear out and begin to crack eventually ...Read morerequiring a replacement. Make sure to check the diagrams of your model for the exact location and the correct installation of this part. Note, this item includes one durable rubber hose and two metal clamps to secure it.

This replacement push-rod is a genuine manufacturer supplied item that is specially designed for Briggs and Stratton engines. The push rod rides on the camshaft to push the exhaust valve open during the exhaust stroke. A bent push rod can seriously affect your engine's performance and it damage the engine if the problem is not taken care ...Read moreof immediately. This part is made out from durable aluminum and it is sold individually.

It is an authentic OEM supplied part that is designed for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. This part provides a seal for the tappet valve. It is an identical replacement for a missing or a faulty part that was included with a new unit. Please make sure to check the appropriate diagrams ...Read moreof your model for exact location and application of this component. Keep in mind this high-quality valve seal is sold individually.

It is a genuine item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. This special gasket is utilized to provide an air-tight seal between connected components, please make sure to refer to the appropriate diagrams of your model for...Read more the correct location and application of this hardware. Keep in mind over time the material may wear out and crack eventually requiring a replacement. It is a high-quality item which is made of durable composite material is sold individually.

This is a genuine manufacturer-sourced part which is designed for use on lawn and garden equipment. It is an identical replacement for a missing or a damaged clamp that is used to secure the hose. Keep in mind this high-quality product is made of durable metal and is sold individually. Please make sure to check the appropriate diagrams for your model for the correct location and application of this hardware.

It is an authentic manufacturer sourced replacement part that is specially designed for use with Briggs and Stratton engines installed on generators and lawn and garden equipment. This gasket provides an air tight seal between the carburetor and the manifold. Over time gaskets tend to deteriorate and crack eventually requiring replacement. It is made out of high-quality composite material and it is sold individually.

This is a genuine manufacturer-approved replacement part which is specially designed for use on Briggs and Stratton engines commonly installed on lawn and garden equipment. The push rod rides on the camshaft to push the exhaust valve open during the exhaust stroke. A bent rod can not only affect your engine's performance, it can seriously...Read more damage other parts if the problem is not taken care of immediately. Keep in mind this high-quality part is made of durable metal and is sold individually.