My Orders
1390M Simplicity Snow Blower - Overview
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$6.40
In Stock
Snow Blower Shear Pin
Part #703063
Shear Pins are designed to break off in order to prevent further damage to your machine. Because they are designed to break, we recommend having a few spares on hand. This part is made of metal, is silver, is not part of a kit or assembly, and is sold individually.
A Shear Pin will break when you hit a large chunk or ice or other debris...Read more. Once it is broken, it will need to be replaced. You will need pliers to complete this repair.
Customers rate this repair as Easy.
Read less
$9.69
In Stock
Engine Oil Seal
Part #795387
This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty as Medium.
This part provides a seal around the crank shaft and engine block. When installing onto the engine block around the crank shaf...Read moret, use something that makes contact around the entire seal, like a large socket or pipe, and tap into place evenly, ensuring that the housing is clean and dry. If the part is broken, likely due to fatigue, there will be leaking oil, and this part should be replaced using the model number on the original part to confirm it is the right fit for your model.
Read less
$6.40
In Stock
Engine Filter
Part #298090S
This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.
Read less
$21.68
In Stock
Gear Universal
Part #1718593SM
The OEM Universal Gear attaches on the chute control rod, and meshes with the worm gear in order to adust the chute. Using the part is rated as "Medium" difficulty by customers, and requires pliers, a socket set, wrench set, drift punch and hammer. If the part breaks there may be broken or chipped teeth which will prevent it from adjustin...Read moreg the chute, and should be replaced. This part is constructed of metal and comes in gold. Refer to your make, model and diagrams to ensure this part is right for your machine.
Read less
$8.09
In Stock
Engine Oil Seal
Part #391086S
The Oil Seal is a manufacturer-approved rubber part which provides a seal between the crankcase and crankshaft by attaching around the axle shaft on the crankhouse housing. Installation is rated as "Medium" difficulty and requires a screw driver, wrench set and seal puller. A broken seal will cause a leak, and the part must be replaced. R...Read moreefer to your make, model and diagram to ensure you're choosing the right part. This part comes in black and gray.
Read less
$6.47
In Stock
Gasket-exhaust
Part #692236
This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in length. Your machine may have a loud hissing or popping sound coming from the exhaust area if the gasket was faulty. You may also notice th...Read moree presence of black soot around the gasket or the exhaust. Your gasket needs to be replaced if it appears worn or deformed. Otherwise, your machine will experience exhaust leaks. To detach the gasket, remove the fasteners that secure it using a socket or wrench. You can detach the gasket from your machine afterwards. Please bear in mind that this replacement part is sold individually.
Read less
$13.02
In Stock
Tube-breather
Part #794683
This item is an authentic OEM replacement part that is intended to be used with small engines from Briggs & Stratton. The breather tube is used to guide the direction of excess gasses and fluid that escape the engine from a higher level of internal pressure. The breather tube is a single item, please see the model diagram for related parts.
$10.65
In Stock
Bearing, Ball 11/16x1
Part #1705897SM
This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.
Read less
$6.40
In Stock
Filter Fuel Mega Pack
Part #394358B
This Fuel Filter is a white plastic part attached within the fuel delivery system between the fuel tank and carburetor. Installation is rated as "Easy" and requires a set of pliers and a screwdriver. If broken, there may be a leak or blockage and the part should be replaced. The part may also need to be replaced according to manufacturer'...Read mores specifications, and is a manufacturer-approved part. Refer to your make, model and diagrams to ensure this part is correct.
Read less
$6.40
In Stock
Seal-o Ring
Part #691917
The Seal-O Ring, also known as the gasket, is red in color, made of rubber, and is an OEM part that requires some skill to replace. This part is designed to create a seal between the carburator and manifold, to prevent air from entering. If your engine loses power, creates a hissing noise, or if the gasket appears damaged or your engine r...Read moreunning improperly it may be time to replace the part.
If you run the engine and spray the outside of the carburator with soapy water, you can test whether or not the gasket is leaking by listening to the sounds produced. If the sound smooths out then you've found your leaky gasket. Damage may occur over time, especially if the part dries out, and make the part appear stretched or worn out.
When making this medium-difficulty repair, make sure the new gasket is fitted properly between the carburetor and intake manifold.
Read less
$6.40
In Stock
Key-flywheel
Part #222698S
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.
$9.69
In Stock
Gasket-crkcse/015
Part #697110
Genuine OEM replacement part used on a variety of Engines. This item is made with Composite Material and it is sold individually. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time this gasket will deteriorate and will need to be replaced. The gasket measures .015 Thick.
Common Symptoms of the 1390M
How this model fails, and the parts that fix it.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Stopped running. Turned to be a bent intake push rod and broken rocker arm
9 of 15 people
found this instruction helpful.
Removed head. Replaced both rocker arms, intake pus rod, push rod guide exhaust and head gaskets. Torqued head in 3 stages to 216 in/lbs. gapped intake to .004 and exhaust to .006 at TDC
Added oil and gas. Now running great
If you need to replace push rods use steel (exhaust) they are the same length
The engine ... Read more was a Briggs & Stratton 217802 0113 E10604 (2006 year date code)
I used the following
796189 gasket
272475S gasket
697494 push rod
690822 push rod guide
691751 rocker arms
Added oil and gas. Now running great
If you need to replace push rods use steel (exhaust) they are the same length
The engine ... Read more was a Briggs & Stratton 217802 0113 E10604 (2006 year date code)
I used the following
796189 gasket
272475S gasket
697494 push rod
690822 push rod guide
691751 rocker arms
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!