136L661F0 MTD - Overview

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

Made of durable silver plastic, this Flange Bearing is an authentic manufacturer-source replacement part for hundreds of models of lawn and garden equipment. It is used to allow a shaft to connect while moving smoothly and freely and is sold individually. When this part malfunctions, you may notice the shaft becomes very sloppy or comes...Read more disconnected. To complete this repair, you will need a screwdriver, a socket set, and pliers. Customers rate this repair as Medium difficulty.

This genuine Steering Shaft is designed to fit all the Lawn Tractor models listed below. It features a 5/8" spline and measures 21.86 inches in length, ensuring a precise fit and reliable performance. A common reason for replacement is wear or stripping of the gear on the shaft, which can lead to steering issues. Before replacing the s...Read morehaft, it’s recommended to inspect the Steering Gear Segment (Part #717-0622C) to determine if it also needs replacement. Replacing both components together can help restore smooth and accurate steering.

Sourced directly from the original manufacturer, this Bell Washer is made of gold-colored metal and is sold individually, not as part of a kit or assembly. It is used to provide spacing between various part assemblies along a shaft. If you hear a strange noise coming from the shaft area, or you notice the Washer is visibly worn or damag...Read moreed, it will need to be replaced. Refer to your owners manual to determine the exact location of this part. Customers rate the difficulty of this repair as Medium.

This starter solenoid is designed to reliably engage the starter motor by allowing a low-power ignition signal to trigger the high-current starting circuit. Built for dependable performance, it helps resolve no-start or intermittent starting issues caused by a failed relay. Ideal for replacing a worn or faulty solenoid, it restores consis...Read moretent starting and reliable operation in lawn mowers, tractors, and snow-clearing equipment.

This silver metal lock washer helps prevent the nut on the drive belt pulley shaft from backing off during operation, it has a 5/16-inch inner diameter and a 1/2-inch outer diameter. one washer is included, replace it if fatigue or damage allows the connected shafts to spin freely, verify fit using the equipment model or owner manual

This plastic bushing supports a moving shaft on select riding mowers and lawn tractors. It helps the shaft turn smoothly and reduces wear. The inside opening is 0.632 inch wide. The outside is about 0.937 inch wide, and the rim is 1.25 inches wide. Use the full mower model number to guarantee the proper fit. Check the parts diagram for its correct location. Replace the bushing if it is cracked, loose, or worn.

The air valve attaches to the wheel and is made of a durable material. This is a genuine MTD, Ryobi, Yard Machines, Bolens, Troy-Bilt, and Yard Man part sourced directly from the manufacturer for use in chippers, shredders, cultivators, edgers, lawn tractors, snowblowers, and trimmers. Keep in mind that this part is sold individually. Whe...Read moren replacing this item a set of pliers might be required during the installation process. It might wear out over time and will need replacing.

This OEM Extension Spring measures .62 x 6.12 inches. It is a silver, metal, individually sold, part. It can be installed with pliers and has been rated Easy to install by customers. (Note: Installation may require a lot of pull force to remove and reattach.) The spring attaches underneath the tractor on the drive belt idler pully, to t...Read morehe axle support bracket, and is used to apply tension on the drive belt idler pully. If broken or overly stretched, likely due to fatigue, you will lose your forward and reverse drive, as the belt will no longer be able to transmit power. If this happens, the part must be replaced. Refer to your owners manual and model number to ensure you are selecting the correct part.

It is an authentic part that is supplied by the original equipment manufacturer for use with lawn and garden equipment. This is a standard hardware which may have multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this component. Keep in mind this high-quality socket cap screw is made of durable metal and is sold individually.

This ball joint connects moving parts in the steering or control linkage of select lawn tractors and snow blowers. It has 3/8-24 male and female right-hand threads. The male threaded end is shorter than a standard joint. Use the complete equipment model and serial number to guarantee the proper fit. Replace the joint if it is loose, bent,...Read more rusted, or hard to move. Before removal, measure the linkage or count the exposed threads so the new joint can be installed in the same position.