136-518-100 (1986) Cub Cadet Lawn Mower - Overview

This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in length. Your machine may have a loud hissing or popping sound coming from the exhaust area if the gasket was faulty. You may also notice th...Read moree presence of black soot around the gasket or the exhaust. Your gasket needs to be replaced if it appears worn or deformed. Otherwise, your machine will experience exhaust leaks. To detach the gasket, remove the fasteners that secure it using a socket or wrench. You can detach the gasket from your machine afterwards. Please bear in mind that this replacement part is sold individually.

The exhaust gasket attaches to the exhaust manifold and helps to form a seal. It is an authentic OEM sourced part which is specially designed for use with Briggs & Stratton generators and engines, plus Toro snowthrowers and lawn tractors. This gasket is made of a flexible material and is priced individually. A screwdriver and a wrench may be needed to install this part.

When the brakes are applied, this brake puck presses against the brake disc in your lawn equipment to help slow down or stop it. The brake puck is in the brake assembly, which might be located near the transmission or the wheels of your machine. If you notice that the machine takes longer to stop or that there is a loud scraping or grindi...Read moreng noise when you push down on the brake, your brake puck may have worn out. If it is not replaced, you risk losing braking power, which leads to equipment damage or accidents. Before any repairs, make sure that your machine is turned off and that the spark plug is disconnected. To dissemble the brake assembly and access the brake puck, use pliers or a wrench to remove any bolts or clips holding it in place. With a screwdriver, pry the brake puck out of your machine. Since this genuine OEM part is sold individually, determine the number of pucks your machine needs by consulting your user manual.

This silver metal lock washer helps prevent the nut on the drive belt pulley shaft from backing off during operation, it has a 5/16-inch inner diameter and a 1/2-inch outer diameter. one washer is included, replace it if fatigue or damage allows the connected shafts to spin freely, verify fit using the equipment model or owner manual

The air valve attaches to the wheel and is made of a durable material. This is a genuine MTD, Ryobi, Yard Machines, Bolens, Troy-Bilt, and Yard Man part sourced directly from the manufacturer for use in chippers, shredders, cultivators, edgers, lawn tractors, snowblowers, and trimmers. Keep in mind that this part is sold individually. Whe...Read moren replacing this item a set of pliers might be required during the installation process. It might wear out over time and will need replacing.

This ground drive belt is for lawn tractors. The ground drive belt turns the transmission pulley to move the tractor.

The Hex Flange bearing, .630 inches I.D. is an OEM part. Black in color and made of metal, it is sold individually. It is installed using a wrench or socket and its installation has been rated as Easy by consumers. This part attaches on the worm gear shaft in the cute, and is used to secure the worm gear on the shaft. If broken, you wil...Read morel no longer to be able to control the chute (or you may only have partial control). This breakage can occur due to fatigue over time, and means the part must be replaced. Refer to your owners manual or model number to ensure you are purchasing the correct part.

This authentic OEM hi-pro key, also called a woodruff key or key stock, is a metal component found in your lawn equipment that connects rotating parts. It is 3/16 inch wide and 5/8 inch long. It fits into a specially-shaped slot on a shaft and prevents the parts from moving or slipping out of position while your machine is running. To fin...Read mored and replace a hi-pro key on your machine, check your user guide for instructions. When removing the hi-pro key, insert a flathead screwdriver or needle-nose pliers into its groove and pry it out of its slot. Please bear in mind that this hi-pro key is sold individually.

This Flat Washer is made of durable gold-colored metal and is an authentic OEM part. It is used to spread the load under a bolt or nut and is sold individually. This part will need to be replaced if you notice any signs of cupping, corrosion, or other damage. Customers rate this repair as Easy.

This genuine component is supplied directly from the original equipment manufacturer for use with Ryobi and MTD lawn and garden equipment. It is a standard hardware which may have multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hex washer screw. Ke...Read moreep in mind this high-quality part is made of durable metal and is sold individually.

It is a genuine item that is supplied by the original manufacturer for use with a variety of lawn and garden equipment. A washer is a special part which helps to provide a tight fit between connected components. It is a standard hardware which may have multiple applications. This part provides an identical replacement for a damaged or a m...Read moreissing hardware that was installed on a new unit. Check the diagrams for your specific model for the exact location and the correct application of this flat washer. Note, it is made of durable metal and is sold individually.

This item is an original part from MTD, Ryobi, Yard Machines, Bolens, Yard Man, and Troy-Bilt for use in lawn tractors. The needle bearing attaches to the input shaft. You may need a wrench and a set of pliers when replacing this part. This item might break over time and will need replacing. It is made of metal and is sold individually.