135O695H7 MTD Lawn Tractor - Overview

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

The Throttle Box Assembly, or the Throttle Assembly, is a kit that includes the housing, handle, and hardware. It is black and constructed of steel and plastic. It can be installed onto the right hand upper handle, using a screwdriver and pliers, and is rated as Medium difficulty to install. This kit contains the parts that control the ...Read moreamount of the air and fuel entering the engine. When the part breaks (likely due to fatigue) you will no longer be able to control the engine. If nothing happens when you move the handle, that means it has become disconnected. When the part is broken it must be replaced. Check your model number to ensure you are selecting the correct replacement part.

Made of durable silver plastic, this Flange Bearing is an authentic manufacturer-source replacement part for hundreds of models of lawn and garden equipment. It is used to allow a shaft to connect while moving smoothly and freely and is sold individually. When this part malfunctions, you may notice the shaft becomes very sloppy or comes...Read more disconnected. To complete this repair, you will need a screwdriver, a socket set, and pliers. Customers rate this repair as Medium difficulty.

Sourced directly from the original manufacturer, this Bell Washer is made of gold-colored metal and is sold individually, not as part of a kit or assembly. It is used to provide spacing between various part assemblies along a shaft. If you hear a strange noise coming from the shaft area, or you notice the Washer is visibly worn or damag...Read moreed, it will need to be replaced. Refer to your owners manual to determine the exact location of this part. Customers rate the difficulty of this repair as Medium.

This starter solenoid is designed to reliably engage the starter motor by allowing a low-power ignition signal to trigger the high-current starting circuit. Built for dependable performance, it helps resolve no-start or intermittent starting issues caused by a failed relay. Ideal for replacing a worn or faulty solenoid, it restores consis...Read moretent starting and reliable operation in lawn mowers, tractors, and snow-clearing equipment.

This silver metal lock washer helps prevent the nut on the drive belt pulley shaft from backing off during operation, it has a 5/16-inch inner diameter and a 1/2-inch outer diameter. one washer is included, replace it if fatigue or damage allows the connected shafts to spin freely, verify fit using the equipment model or owner manual

This flat idler pulley is designed to help maintain proper belt tension while reducing vibration and uneven wear in lawn and snow equipment drive systems. Made from durable metal for long-lasting performance, it supports smooth belt routing and consistent operation under regular use. Ideal for replacing a worn or noisy pulley, it helps restore reliable belt engagement and overall machine performance.

The air valve attaches to the wheel and is made of a durable material. This is a genuine MTD, Ryobi, Yard Machines, Bolens, Troy-Bilt, and Yard Man part sourced directly from the manufacturer for use in chippers, shredders, cultivators, edgers, lawn tractors, snowblowers, and trimmers. Keep in mind that this part is sold individually. Whe...Read moren replacing this item a set of pliers might be required during the installation process. It might wear out over time and will need replacing.

This OEM Extension Spring measures .62 x 6.12 inches. It is a silver, metal, individually sold, part. It can be installed with pliers and has been rated Easy to install by customers. (Note: Installation may require a lot of pull force to remove and reattach.) The spring attaches underneath the tractor on the drive belt idler pully, to t...Read morehe axle support bracket, and is used to apply tension on the drive belt idler pully. If broken or overly stretched, likely due to fatigue, you will lose your forward and reverse drive, as the belt will no longer be able to transmit power. If this happens, the part must be replaced. Refer to your owners manual and model number to ensure you are selecting the correct part.

This sealed ball bearing is used in mower deck spindle and pulley assemblies to reduce friction and support smooth rotation. Designed to fit securely in the housing, it helps extend component life and maintain consistent cutting performance. It’s a direct replacement for worn or noisy bearings during deck or pulley service.

This ball joint connects moving parts in the steering or control linkage of select lawn tractors and snow blowers. It has 3/8-24 male and female right-hand threads. The male threaded end is shorter than a standard joint. Use the complete equipment model and serial number to guarantee the proper fit. Replace the joint if it is loose, bent,...Read more rusted, or hard to move. Before removal, measure the linkage or count the exposed threads so the new joint can be installed in the same position.

The Push Cap is a black plastic cap which secures to the end of a shaft to prevent injury. It can be installed with a hammer and is rated as "Easy" to install. If the part appears damaged or worn down in a way that could cause injury, it should be replaced. Refer to your make, model and diagrams to check if this is the right part for you.