This burner bowl or drip pan is found beneath the heating element on your cooktop or range. This part measures 8 inches in diameter, and should not be confused with the smaller pan, which measures 6 inches in diameter. The burner bowl collects spills that may build up when cooking on your range. If your old 8-inch burner bowl is cracked, broken, or missing, this is the part that can replace it.
This is an OEM replacement part and is sold individually. Its propose is to deliver an electric current from an ignition system to the combustion chamber of a gas fueled engine. It will ignite the air fuel mixture by the spark. Spark Plugs will usually have to gapped to the manufactures specifications found in the owners manual. Over tim...Read moree a Spark Plug will become fouled because the air/fuel ratio may be set wrong,worn piston rings, carbon build up and other factors. It is better to replace a fouled spark plug, rather then trying to clean it.
This light bulb lens covers the interior light bulb in an oven, range, or stove. No tools are necessary to replace this part. Simply slide off the wire bracket to remove the existing light bulb lens. Disconnect power to your appliance before this repair. It is recommended to check the light bulb while the lens cover is removed in case it ...Read moreneeds to be replaced. Be sure to remove all broken glass, if applicable, before installing new lens. This part is sourced directly from the genuine manufacturer, and is sold individually.
This is a replacement carburetor overhaul kit for your small engine. The carburetor is essential to the overall performance of your engine, and the carb can get clogged up over time for a variety of reasons. When your carb becomes clogged, it is often a good idea to take it apart and replace the various parts inside by purchasing a carbur...Read moreetor kit. This is a 15-piece set and contains everything that you will need to do a total overhaul of your carburetor. You may want to purchase some carb cleaner as well, to ensure that the new pieces in the carb kit fit and adhere properly.
This part provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).
These are replacement screws designed to fit your range. They are made of metal and are approximately ¼ inch long. They come in a package of 12. These are OEM parts sourced directly from the manufacturer.
This grommet is an OEM part that is a 45-degree elbow for the crankcase breather tube of your mower engine. That is why it is also known as a 45-degree breather tube.
The part is made of rubber and is black in color. You must purchase this part individually. Your grommet may require replacing if you notice dark smoke coming out of the e...Read morexhaust. This is a telltale sign that your grommet has become cracked and damaged. Other symptoms are a reduction in the mower performance, or a backfiring engine. According to our customers, this is an easy repair.
It requires no tools. Simply attach the grommet to the breather tube from the crankcase to the carburetor.
The manufacturer-approved Ratchet Pawl (Starter Pawl) comes in a set of two (2). This part attaches inside the recoil assembly, and is used to engage the flywheel. if broken due to wear/damage it will have a hard time engaging the fly wheel, making the engine harder to start, and should be replaced. Installation is rated as "Easy" by cust...Read moreomers, and will require a screwdriver, pliers and nutdriver. Refer to your make, model and diagram to ensure this is the correct part for you.This model is plastic and comes in white.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
terminal block melted
56 of 77 peoplefound this instruction helpful.
jonathan from willow springs, IL
Easy
Less than 15 mins
Nutdriver, Screw drivers
The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. U
... Read morenscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient
Read less
Was this helpful?
Thank you for voting!
5 HP Briggs and Stratton chipper shredder - no spark
19 of 26 peoplefound this instruction helpful.
Thomas from ALFRED, ME
Difficult
30 - 60 mins
Nutdriver, Pliers
Removed old sparkless magneto, replaced with new part PS9278124 Magneto, and still no spark. The only conclusion that I can draw, is this magneto is defective,
Was this helpful?
Thank you for voting!
Original terminal block plastic shielding melted, protecting appliance when the wires overheated.
6 of 8 peoplefound this instruction helpful.
Brian from DOVER, PA
Really Easy
30 - 60 mins
Nutdriver
Safety first * Unplugged 220 VAC from outlet. Removed shield cover screws with 1/4" hex nut driver (5 screws). Removed all 6 silver screws from terminal block with 1/4" nut driver, freeing all wires. Removed the green ground screw and ground bracket from center terminal. Cut away (using the drill) melted original terminal block plastic to
... Read more access the 2 black 1/4" nuts holding original terminal block onto appliance. Discarded the original damaged terminal block. Attached the new terminal block, aligning the mounting holes and the terminal block the same way the original terminal block was lined up and re-used the black 1/4" nuts (original used because the replacement package did not include new black screws). I bought a new appliance cord, since the original cord overheated. Reattached all wires using the 6 new silver screws. Start with the middle terminal by attaching the appliance wires and the ground bracket. The ground must be attached to the bracket and the bracket bridges between the terminal block and the range body. Reattached shield cover. Plugged in appliance. Note: it doesn't matter which outside wire attaches to the outside terminals (both are hot), but the middle wire (neutral) must attach to the middle terminal. However, the ring terminal should be flush on the terminal block so you don't bend the ring.