12M4 (016601) Ariens Lawn Tractor - Overview

The Friction Wheel is part of the clutch assembly, which helps to drive your unit. If broken from being worn down, you will have drivability problems and should replace the part. This part is metal with a rubber outer ring, and comes in white/black. Installation will require a wrench set, socket set, and pliers and is rated as "Medium" di...Read morefficulty by customers. Refer to your make, model and diagram to check if this is the right part for you.

This OEM-sourced flange bushing supports smooth movement in your lawn equipment by reducing friction. This bearing has an inner diameter of 0.625 inches, an outer diameter of 0.750 inches, a width of 0.5 inches, and a flange diameter of 0.875 inches. Depending on the model and make of your machine, this bushing can be found in various par...Read morets of your machine, such as pivot points, axles, and spindles. A damaged bushing causes increased friction, misalignment, and grinding or squeaking noises. Your machine may need expensive repairs and may eventually fail if you do not replace a broken bushing. To remove an existing bushing, you need to remove components that provide access to the flange bearing. Consult your user manual if needed. Locate the bearing and use a screwdriver or wrench to remove any clips, screws, or bolts securing it. Use a bearing puller tool or a mallet to pull or tap the bearing out of your machine if necessary. Please note that the bushing is sold individually.

This authentic part is supplied by the original manufacturer for use with Ariens lawn and garden equipment. The flange bushing helps to provide a tight seal between connected parts while allowing for movement with minimum friction. Over time it may wear out, get damaged or lost eventually requiring a replacement. This high-quality flange ...Read morebushing is made of durable material and is sold individually. A screwdriver, pliers and a wrench set might be needed to perform this repair. Make sure to refer to the appropriate diagrams for your model to ensure the proper replacement procedure.

This is a genuine item that is supplied from the original equipment manufacturer for Ariens lawn and garden equipment. It is an identical replacement for missing or a faulty roll pin that was installed on a new unit, please make sure to refer the appropriate diagrams of your model for the correct location and application of this hardware....Read more Keep in mind this high-quality part is made of durable metal and is sold individually.

This is an original Ariens replacement part manufactured for use with snowthrowers. The special feather key is used to protrude from a slot on a shaft and fit into a keyway on a gear or part assembly that fits over the shaft. The feather key joins the shaft and gear to allow unison rotation. This feather key is sold individually, please see model diagram for associative parts.

This authentic OEM sourced replacement part is specially designed for use with Ariens lawn and garden equipment. The ball bearings are used to reduce friction between rotating parts, the rollers help to distribute the weight evenly while the minimal contact area reduces friction. Over time components may wear out and begin to crack event...Read moreually requiring a replacement, please note this high-quality metal bearing is sold individually.

Often located on the front gear shaft, this Roll Pin has been sourced directly from the original manufacturer for use on various machines. It is 1-1/4 inch in length, made of durable black metal, is not part of a kit or assembly, and is sold individually. In order to complete this repair, you will need pliers, a screwdriver, and a hammer and tap. Customers rate this repair as Easy.

This Bearing Cone, or Cone Bearing, is used to support the helicon pinion shaft to allow it to rotate where it passes through an assembly. It is sourced directly from the manufacturer for use in snow blowers, is made of metal, is silver, is not part of a kit or assembly, and is sold individually. A grinding, growling, or squealing sound ...Read morefrom your bearing suggests that your bearing cone will need to be replaced. If you find signs of wear, fatigue, or damage on the Cone, it needs to be replaced. You will need a wrench set, a socket set, a screwdriver, and a nut driver to complete this repair. When you install the new Cone, ensure that you pack the bearing with grease before installing it. Customers rate this repair as Medium difficulty.

This genuine OEM lock nut is designed for use with Ariens snow blowers and throwers. It helps secure the skid shoe runner to the deck and is engineered to resist loosening when properly threaded onto a bolt, ensuring a stable and reliable connection. Made from durable metal, this high-quality part is sold individually. For safe installation, be sure to use a properly sized wrench.