My Orders
12AE764N010 (2009) Cub Cadet Lawn Mower - Overview
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$9.69
In Stock
Engine Oil Seal
Part #795387
This OEM Seal-Oil (PTO Side), also called the Oil Seal, is a Black, Nitrile Rubber, 2/14 O.D., individually sold part which is installed using a Seal Puller. Customers rate the installation difficulty as Medium.
This part provides a seal around the crank shaft and engine block. When installing onto the engine block around the crank shaf...Read moret, use something that makes contact around the entire seal, like a large socket or pipe, and tap into place evenly, ensuring that the housing is clean and dry. If the part is broken, likely due to fatigue, there will be leaking oil, and this part should be replaced using the model number on the original part to confirm it is the right fit for your model.
Read less
$6.40
In Stock
Engine Filter
Part #298090S
This is a round, inline fuel filter with 0.25-inch nipples, used in a variety of lawn and garden equipment. It is sourced from the original equipment manufacturer and has the capability to filter out particles as small as 150 microns in size. The filter is designed to remove any dirt or debris in the fuel to avoid contaminating the engine...Read more. Over time, it is common for the filter to become clogged with dirt/debris or damaged, resulting in less fuel entering the engine, engine misfiring, stalling, and overall lower performance from your equipment. To replace the faulty fuel filter, first disconnect the fuel lines with pliers or a clamp tool and then pull out the old filter. Install the new filter into the housing and reattach the fuel lines to complete your repair.
Read less
$6.40
In Stock
Lawn Mower Self-Tapping Screw
Part #710-04484
$6.40
In Stock
Carriage Bolt 5/16-18 x 3/4" Lg.
Part #710-0451
This carriage bolt measures 5/16-18 x .75 and fastens two parts in your machine together. It has a round domed head and a square underside so the bolt does not rotate once it has been secured into place. If it has signs of deformation or wear, you will need to replace it. To unthread this bolt, you need an adjustable wrench to loosen the ...Read morenut found on the end of the bolt. You may need to apply a lubricating oil to the bolt if it is stuck. You may need to clamp down on the head of the bolt with pliers while continuing to turn the nut counterclockwise. You can then slide the carriage bolt out of its hole or tap it gently with a hammer. This bolt is a standalone product and the nut is not included. This bolt was sourced directly from its manufacturer.
Read less
$6.40
In Stock
Lawn Mower Hex Washer Head Screw
Part #710-0599
This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.
Read less
$6.47
In Stock
Gasket-exhaust
Part #692236
This OEM exhaust gasket in lawn and garden equipment creates a seal between the engine block and the muffler or exhaust pipe so that exhaust gases do not leak. This is 3.30cm in diameter and 6.35cm in length. Your machine may have a loud hissing or popping sound coming from the exhaust area if the gasket was faulty. You may also notice th...Read moree presence of black soot around the gasket or the exhaust. Your gasket needs to be replaced if it appears worn or deformed. Otherwise, your machine will experience exhaust leaks. To detach the gasket, remove the fasteners that secure it using a socket or wrench. You can detach the gasket from your machine afterwards. Please bear in mind that this replacement part is sold individually.
Read less
$13.02
In Stock
Tube-breather
Part #794683
This item is an authentic OEM replacement part that is intended to be used with small engines from Briggs & Stratton. The breather tube is used to guide the direction of excess gasses and fluid that escape the engine from a higher level of internal pressure. The breather tube is a single item, please see the model diagram for related parts.
$6.40
In Stock
Nut-flglk 5/16-18
Part #712-04063
This nut is a manufacturer-approved replacement part for various lawn and garden equipment. It is sold individually, not as part of a kit or assembly. Also referred to as a Lock Nut, it is resistant to loosening when threaded on a bolt. It has a variety of applications and is used in multiple locations on most models. Please refer to your...Read more owners manual to determine the exact location.
While made of durable metal, the ends can round off from improper use of a wrench or socket. Depending on the location, this part may also become worn through regular use of your machine. It should be replaced when visibly cracked, worn or damaged. To complete this repair, you will need a wrench or socket, and a torque wrench. Ensure you torque the bolt according to the manufacturer recommendations.
Customers rate this repair as Easy.
Read less
$6.40
Special Order
Seal-o Ring
Part #691917
The Seal-O Ring, also known as the gasket, is red in color, made of rubber, and is an OEM part that requires some skill to replace. This part is designed to create a seal between the carburator and manifold, to prevent air from entering. If your engine loses power, creates a hissing noise, or if the gasket appears damaged or your engine r...Read moreunning improperly it may be time to replace the part.
If you run the engine and spray the outside of the carburator with soapy water, you can test whether or not the gasket is leaking by listening to the sounds produced. If the sound smooths out then you've found your leaky gasket. Damage may occur over time, especially if the part dries out, and make the part appear stretched or worn out.
When making this medium-difficulty repair, make sure the new gasket is fitted properly between the carburetor and intake manifold.
Read less
$9.69
In Stock
Gasket-crkcse/015
Part #697110
Genuine OEM replacement part used on a variety of Engines. This item is made with Composite Material and it is sold individually. Its purpose is to make an air tight seal so that no air/oil leakage occurs. Over time this gasket will deteriorate and will need to be replaced. The gasket measures .015 Thick.
$6.40
In Stock
Lawn Mower Flanged Lock Nut
Part #712-04065
Designed for use in various models of lawn and garden equipment, this part is not sold as part of a kit or assembly. It is made of metal, is gold in color, and is sold individually. This part may also be called a Flange Lock. This nut is designed to lock in place, preventing vibrations and other parts coming loose.
This nut may be locate...Read mored in multiple locations on your machine, refer to your owners manual to determine if this is the correct part. You will need a wrench or socket set and a torque wrench to complete this repair. You should only torque the nut to the manufacturer recommendation, no tighter.
You will need to replace this part when it is worn or damaged. While this part can wear through regular use, it is most commonly damaged through improper use of a wrench or socket.
Customers describe this repair as Easy.
Read less
$64.16
In Stock
Engine Ignition Coil
Part #595304
Ignition coil 595304 is an original equipment manufacturer (OEM) part that fits Briggs & Stratton lawn and garden equipment engine models 31R907-0018-G1, 33R877-0002-G1, 33R877-0009-G1 and 33S877-0015-G1.
Ignition coil 595304 generates the voltage for the spark plug.
Set the ignition coil air gap at 10/1000-in to 14/1000-in.
Torque the ignition coil screws to 30-lb-in.
Common Symptoms of the 12AE764N010
How this model fails, and the parts that fix it.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Stopped running. Turned to be a bent intake push rod and broken rocker arm
9 of 15 people
found this instruction helpful.
Removed head. Replaced both rocker arms, intake pus rod, push rod guide exhaust and head gaskets. Torqued head in 3 stages to 216 in/lbs. gapped intake to .004 and exhaust to .006 at TDC
Added oil and gas. Now running great
If you need to replace push rods use steel (exhaust) they are the same length
The engine ... Read more was a Briggs & Stratton 217802 0113 E10604 (2006 year date code)
I used the following
796189 gasket
272475S gasket
697494 push rod
690822 push rod guide
691751 rocker arms
Added oil and gas. Now running great
If you need to replace push rods use steel (exhaust) they are the same length
The engine ... Read more was a Briggs & Stratton 217802 0113 E10604 (2006 year date code)
I used the following
796189 gasket
272475S gasket
697494 push rod
690822 push rod guide
691751 rocker arms
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!