128C (2010-08) Husqvarna Trimmer - Overview

This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this essential component ensures clean fuel delivery, protecting the engine from potential damage caused by contaminants. Sold individually, the filt...Read moreer is built to meet original equipment standards for fit and function. Over time, the filter may become clogged, restricting fuel flow and making engine starts more difficult. For optimal performance, it should be replaced—not cleaned—at the first sign of blockage or wear.

This Fuel Line is a 25-inch, clear, plastic line used to deliver fuel. It requires a screwdriver, pliers, socket set, and nut driver and is rated as "Easy" to install by customers. If the fuel line wear out to the point of breaking, cracks and/or leaking will appear and the part should be replaced. Refer to your make, model and diagram to ensure this is the correct part for you.

The air filter prevents dirt and debris from entering the engine on your lawn equipment. This is an OEM filter that is white, roughly 2x3.5 inches in dimension, and can only be purchased individually. Made of foam, the air filter becomes clogged and worn over time, causing the engine to run rough from restricted air flow. You can make t...Read morehis repair easily with no required tools by inserting the new filter inside the air cleaner housing of your engine.

The Fuel Line Fitting is a plastic part which attaches two pieces of fuel line together. If broken due to damage/fatigue, there may be a leak and the part must be replaced. Installation is rated as "Easy". Refer to your make, model and diagram to ensure this part is correct for you.

This replacement throttle housing is specially designed for use with Husqvarna trimmers and edgers. It is an authentic OEM sourced part, not an aftermarket imitation. This is the left hand side plastic housing piece only. Please note, the right hand side housing piece and the hardware to secure the two pieces together are all sold separately. To complete this repair you will need a screwdriver.

This carburetor mixes air and fuel to power small engines, helping ensure smooth starting and reliable performance. Built from durable materials, it supports consistent fuel delivery and efficient operation. Replacing a worn or faulty carburetor can resolve issues such as hard starting, rough idling, or poor acceleration, restoring proper engine function.

This is an OEM part guaranteed to fit Milwaukee power tools. This trigger spring is attached to main trigger. Please note that only trigger spring is included. When disassembling this area, be sure to slowly separate parts in order to prevent springs from being lost when released too quickly. Though they appear similar, a lockout spring i...Read mores a different part used with the throttle lockout (not present in all models). This part is often purchased with: • Trigger, part # 545066001 • Throttle Lockout, part # 530059804 • Lockout Spring, part # 545045601

This purge bulb is an authentic OEM part from Craftsman for gas blowers, trimmers, blowers and weed wackers. This part disperses fuel to the carburetor to provide starting the blower faster. You will need a screw driver to replace this part. This purge bulb is made of rubber and sold individually.

This is an authentic OEM part used in the Husqvarna trimmers listed below. This is the main trigger throttle mechanism attached to lower part of handle. While disassembling handle for this repair, be sure to separate pieces carefully so that no springs are lost. Note detailed positioning of all parts before removing them; proper positioni...Read moreng is vital to tool functioning. Sold individually. Throttle trigger spring is available separately, as part # 530016454. Note that this trigger fits serial number 2010-73N and higher. For lower serial number models, see trigger part # 545066001.

The Starter Pawl bridge provides the resistance needed for the starter rope to start the trimming engine. It is an OEM part that attaches inside the recoil assembly. If broken due to weaar or fatigue, the engine will not engaged when the rope is pulled, and the part should be replaced. Installation is rated as easy and requires a screwdrv...Read moreier, pliers and nutdriver. Refer to your make, model and diagram to check if this part is correct. This part is metal, individually sold, and comes in gold.

This is an authentic OEM sourced replacement starter housing which is designed for use with Husqvarna lawn and garden equipment. It is the starter housing assembly which is used to pull-start the engine. It is a complete assembly which includes a durable plastic housing, starter pulley, starter spring, and the pull rope with the grip, please note the hardware to secure this assembly is sold separately.

This item has been sourced from the original manufacturer to be used with trimmers and edgers from Husqvarna and Jonsered. The wire harness is a complete part assembly that includes the throttle cable and control wires. This item is used to run the motor, and to adjust the engines out by linking the control handles. This item is priced as a single item.