125B Husqvarna Leaf Blower / Vacuum - Overview

This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this essential component ensures clean fuel delivery, protecting the engine from potential damage caused by contaminants. Sold individually, the filt...Read moreer is built to meet original equipment standards for fit and function. Over time, the filter may become clogged, restricting fuel flow and making engine starts more difficult. For optimal performance, it should be replaced—not cleaned—at the first sign of blockage or wear.

Genuine Husqvarna kit. This kit contains the fuel lines, fuel filter and primer bulb and grommet for all of the Husqvarna Blowers listed below. This makes it very convenient when you need all of the separate parts. You can order them in one kit.

Also referred to as a Recoil Spring, this OEM replacement part is used to rewind the pull rope back into the starter housing. This Spring is sold individually, not as part of a kit or assembly, and is made of metal. If the pull cord will not retract into the housing, inspect the Recoil Spring for signs of wear or damage, replacing if ne...Read morecessary. You will need a screwdriver to complete this repair. Customers rate this repair as Easy.

This replacement knob is used to secure the air filter cover. It is an authentic Husqvarna part sourced directly from original equipment manufacturer. It is commonly used on gas powered trimmers, edgers and blowers. This assembly consists of a plastic knob/handle and a threaded metal shaft. This item is sold individually.

Compatible with over 150 models of lawn equipment, this Spark Plug has been sourced directly from the original manufacturer. It is sold individually, made of metal and ceramic components, and is not part of a kit or assembly. The spark plug is used to ignite the air-fuel mixture inside the combustion chamber. You may need to replace the...Read more Spark Plug if your 1 cylinder engine won't start, or if your more-than-1 cylinder engine runs rough. Spark Plugs will wear over time and should be inspected regularly. Customers rate this repair as Easy.

This is an authentic replacement part supplied from Poulan. It is generally used with gas powered chainsaws. This nut in conjunction with a bolt (sold separately) helps to secure air filter and carburetor. Requires a wrench installing/removing this item. It is sold individually.

This is a standard hardware which has multiple applications based on your tool. It is sourced from original equipment manufacturer for use with a variety of power equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. Requires a hex key or an allen wrench to install or remove it.

This genuine manufacturer sourced replacement part is specially made for use with a variety of handheld lawn and garden equipment. This part is installed on top of the piston/connecting rod. Its purpose is to create a seal in the cylinder so that it can build pressure. A worn or broken piston ring will allow combustion gases to escape the...Read more seal and enter the crankcase, causing low compression and a loss of power. If compression is reduced significantly, the engine will not run at all. Includes one (1) metal piston ring. Tools Required: Receptacle for draining fuel, Torx wrenches, spark plug wrench, 10mm wrench (or adjustable), long-nosed pliers, rubber mallet, standard screwdriver, old starter rope (or similar cord), adjustable pliers, 2-cycle engine oil, razor blade, ignition gapping gauge. • Remove the air cleaner • Drain the fuel • Remove the air cleaner case • Remove the carburetor • Remove the intake insulator • Remove the spark plug • Remove the engine cover • Remove the insulator gasket • Remove the starter assembly • Remove the fuel tank • Remove the air duct • Separate the engine • Bind the engine • Remove the clutch • Remove the flywheel • Remove the starter pulley • Unbind the engine • Remove the muffler • Separate the cylinder from the crankcase • Remove the piston ring • Install the piston ring

This is an original Husqvarna replacement part manufactured for use with leaf blowers. The plastic tube is the upper part of the tube assembly that connects to the blower housing when using the vacuum attachment. This upper vacuum tube assembly is available as an individual replacement part, please note the lower tube is available separately.

This is a genuine Manufacturer Approved replacement part for use with some Husqvarna Backpack Blowers. It is designed to keep the fuel in the fuel tank. It includes a retainer that remains in the tank to keep the fuel cap from being lost or falling on the ground.