122RJ Husqvarna Brush Cutter - Overview

This replacement throttle housing is specially designed for use with Husqvarna trimmers and edgers. It is an authentic OEM sourced part, not an aftermarket imitation. This is the left hand side plastic housing piece only. Please note, the right hand side housing piece and the hardware to secure the two pieces together are all sold separately. To complete this repair you will need a screwdriver.

This replacement throttle housing is a high quality OEM item that is specially designed for Husqvarna string trimmers and edgers. This is the right hand side plastic housing piece, please note that the left hand side piece and the hardware to secure the two halves are all sold separately. To complete this repair you will need a screwdriver.

This is an OEM part guaranteed to fit Milwaukee power tools. This trigger spring is attached to main trigger. Please note that only trigger spring is included. When disassembling this area, be sure to slowly separate parts in order to prevent springs from being lost when released too quickly. Though they appear similar, a lockout spring i...Read mores a different part used with the throttle lockout (not present in all models). This part is often purchased with: • Trigger, part # 545066001 • Throttle Lockout, part # 530059804 • Lockout Spring, part # 545045601

This is an authentic OEM part used in the Husqvarna trimmers listed below. This is the main trigger throttle mechanism attached to lower part of handle. While disassembling handle for this repair, be sure to separate pieces carefully so that no springs are lost. Note detailed positioning of all parts before removing them; proper positioni...Read moreng is vital to tool functioning. Sold individually. Throttle trigger spring is available separately, as part # 530016454. Note that this trigger fits serial number 2010-73N and higher. For lower serial number models, see trigger part # 545066001.

The Starter Pawl bridge provides the resistance needed for the starter rope to start the trimming engine. It is an OEM part that attaches inside the recoil assembly. If broken due to weaar or fatigue, the engine will not engaged when the rope is pulled, and the part should be replaced. Installation is rated as easy and requires a screwdrv...Read moreier, pliers and nutdriver. Refer to your make, model and diagram to check if this part is correct. This part is metal, individually sold, and comes in gold.

This is a genuine part that is supplied by the original manufacturer for use with Husqvarna and Jonsered trimmers and edges. The air filter cleans the air entering and exiting the carburetor. This part is a common wear item, we recommend replacing the air filter periodically. For this repair, you will need a pair of pliers and a screwdriv...Read moreer to remove any covers or shrouds. Be sure to unplug the spark plug and boot wire before starting this repair.

This is an authentic OEM part from Husqvarna for use with Line Trimmers. The recoil starter assembly spins the flywheel to start the engine. This assembly includes the recoil starter cover. The most common reason for replacing the starter assembly is if it is damaged or will not start the engine properly. This part is sold individually. T...Read morehe tool that you will need to replace the starter assembly is a T-25 Torx head screwdriver.

This throttle assembly is designed for handheld outdoor power equipment to transmit throttle trigger input to the carburetor for smooth, accurate engine speed control. Built with a durable cable and protective housing, it supports consistent acceleration and dependable operation during use. It’s a practical replacement for restoring proper throttle response when the original cable becomes worn, stretched, or damaged.

This is an authentic OEM sourced replacement part that is intended to be used with trimmers, brushcutters, and edgers from Husqvarna and Jonsered. The metal nut is used with several different types of machines and the application of the nut can vary based on the model of the equipment. This nut is sold individually.

This item has been OEM sourced to ensure a high level of quality. The gearbox assembly is intended to be used with trimmers from Husqvarna and Jonsered. The gearbox attaches to the bottom of the lower drive shaft. This item is used to connect the rotation of the shaft with the rotation of the cutting head. This gearbox is sold as an individual replacement part.

This is a genuine replacement part manufactured for use with trimmers. The shield bracket is used to secure the deflector shield to the trimmer shaft. The shield bracket is sold individually, please see model diagram for associative parts.

This is a genuine manufacturer-sourced replacement part which is specially designed for use with Husqvarna lawn and garden equipment. It is an identical replacement for a missing or damaged hexagon nut that was installed on a new unit. This is a standard hardware which has multiple applications, please make sure to refer to the appropriat...Read moree diagrams of your model for the correct location and application of this component. Keep in mind this high-quality nut is made of durable metal and is sold individually.