This is a replacement air filter/AC cartridge for your small engine. The air filter prevents dirt and debris from entering the engine. Over time, the air filter can become clogged or damaged, and this can lead to reduced performance. This air filter is approximately 4 inches wide and approximately 5 inches long. To replace the air filter,...Read more locate the air filter cover on the side of the engine, unscrew it, and remove the old filter. Be sure to clear out any dirt, clippings, or other debris that has found its way into the air filter assembly before you insert the new filter. Reattach the air filter cover, and secure it with the screws. This product is sold individually.
The manufacturer-approved Ratchet Pawl (Starter Pawl) comes in a set of two (2). This part attaches inside the recoil assembly, and is used to engage the flywheel. if broken due to wear/damage it will have a hard time engaging the fly wheel, making the engine harder to start, and should be replaced. Installation is rated as "Easy" by cust...Read moreomers, and will require a screwdriver, pliers and nutdriver. Refer to your make, model and diagram to ensure this is the correct part for you.This model is plastic and comes in white.
This spark plug is designed to provide reliable ignition and efficient fuel combustion in small engine applications. Built for consistent performance and durability, it helps maintain smooth operation, steady power output, and easier starting. Ideal for routine maintenance or replacement, it supports dependable engine performance in lawn and garden equipment, generators, and similar outdoor power machines.
Genuine Manufacturer Sourced replacement part used on a variety of Briggs and Stratton Engines. This filter adds a second layer of protection against airborne-dirt particle ingestion. This is a Foam Pre-Cleaner which is Sold Individually. Please note a Paper Filter and a Cover are both Sold Separately.
This is a genuine OEM sourced replacement part. It is designed for use with lawn and garden engines. It is an important part of the starter assembly that is used to crank start the unit. Please note shroud/housing, starter pulley, starter spring, grip, the pull rope and the hardware are all sold separately. This pawl plate is made out of ...Read moreplastic and it is sold individually. To complete this repair you would need a wrench.
This genuine fuel tank assembly is sourced directly from the original equipment manufacturer and is specifically designed for use with Briggs & Stratton engines on lawn and garden equipment. It serves as the primary reservoir for storing fuel required by the engine.
Constructed from durable plastic, this assembly includes both the fuel...Read more tank and cap.
Note: Mounting hardware and fuel lines are sold separately. This tank features four mounting holes for secure installation.
For proper fit and installation, refer to your equipment’s model diagram.
This OEM Oil Seal is an individually sold rubber part which is attached around the axis shaft on the crankcase housing to provide a proper seal. A broken seal will lead to a leak, and the part should be replaced. Installation is rated as "Medium" difficulty by customers, and will require a screwdriver, wrenchset and seal puller. Refer to ...Read moreyour make, model and diagrams to ensure you've chosen the correct part. This model comes in black and grey.
This is an authentic OEM sourced replacement part that is intended to be used with lawnmower engines and outboard motors from Briggs & Stratton and Toro. The metal screw is used to secure the rocker cover to the cylinder head assembly. This item is available as an individual replacement part.
The exhaust gasket attaches to the exhaust manifold and helps to form a seal. It is an authentic OEM sourced part which is specially designed for use with Briggs & Stratton generators and engines, plus Toro snowthrowers and lawn tractors. This gasket is made of a flexible material and is priced individually. A screwdriver and a wrench may be needed to install this part.
This item is a genuine replacement part that has been OEM sourced and is intended to be used with lawnmower engines from Briggs & Stratton and Toro. The rubber seal is used to prevent oil from leaking at the connection between the bottom of the oil fill tube and the crankcase. This item also allows the fill tube to firmly sit into the case. The dipstick tube seal if available as an individual replacement part.
This is a genuine manufacturer-sourced part which is designed for use on lawn and garden equipment. It is an identical replacement for a missing or a damaged clamp that is used to secure the hose. Keep in mind this high-quality product is made of durable metal and is sold individually. Please make sure to check the appropriate diagrams for your model for the correct location and application of this hardware.
Removed old broken rewind starter (4 bolts); found the Model and Serial numbers; found Parts Direct and ordered new assembly; upon delivery, reinstalled with new Starter and hardware.
Was this helpful?
Thank you for voting!
Generator would not start, Birggs & Stratton recommended to replase Gasket Exhaust.
12 of 46 peoplefound this instruction helpful.
Alberto from PALMETTO BAY, FL
Really Easy
30 - 60 mins
Socket set
Remove the spark suppresser, 4 face screws, 2 bottom screws and the two screws the hold the gasket. I also had to back out the top screw of the cover it blocked and prevented the removal of the gasket.