121-528R352 (1991) MTD Lawn Mower - Overview

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

The Lever and Knob Assembly (or Front Wheel Height Adjuster) is used to adjust the front height of the mower, and attaches on the front wheels. It can be installed using a socket set and wrench set, and is rated as "easy" to install by our customers. If broken or damaged (likely due to general wear over time) you will no longer be able to...Read more move it to make adjustments, and the part should be replaced. This black, plastic part is sold individually. Refer to your make, model and diagrams to ensure this part fits your machine.

This hinge pin is an OEM part that is designed to hold the chute to the bracket of your lawn mower, allowing the shute to move upward and downward. It is silver, made of metal, and it is around 5 inches in length. Over time, the hinge pin may break, and it will no longer be able to support the chute or allow it to move. If this occurs, ...Read moreyou will need a pair of needle nose pliers to complete this simple repair, which most of our customers told us was easy. Look for the hinge pin on the chute door and the mounting bracket of your mower deck.

This is the lower handle for various models of walk-behind lawn mowers. This handle is made of durable black metal and attaches directly to the rear of the lawn mower. This handle is an OEM part that is sold by itself and does not come with any hardware or other parts. If your current lower lawn mower handle is corroded or damaged, it nee...Read moreds to be replaced immediately so you can properly and safely handle your lawn mower. This handle measures approximately 24.5-inches long and 17-inches wide and connects the rear of the lawn mower with the upper and main handle that the user holds when operating the lawn mower. Replacing this handle will not require any tools but must start with turning off the lawn mower. Loosen and remove the knobs around the handle, including the ones connecting the lower handle to the mower and those securing the upper and lower handles. Once each knob is removed, replace the old lower handle with the new one, and resecure • all the knobs onto the handle(s).

Sourced directly from the original manufacturer, this Bell Washer is made of gold-colored metal and is sold individually, not as part of a kit or assembly. It is used to provide spacing between various part assemblies along a shaft. If you hear a strange noise coming from the shaft area, or you notice the Washer is visibly worn or damag...Read moreed, it will need to be replaced. Refer to your owners manual to determine the exact location of this part. Customers rate the difficulty of this repair as Medium.

This silver metal lock washer helps prevent the nut on the drive belt pulley shaft from backing off during operation, it has a 5/16-inch inner diameter and a 1/2-inch outer diameter. one washer is included, replace it if fatigue or damage allows the connected shafts to spin freely, verify fit using the equipment model or owner manual

This genuine OEM carriage bolt is used to secure various parts in lawn and garden outdoor equipment. The bolt has a round head with a square area underneath it that prevents the bolt from turning and coming loose when it is installed. The bolt shaft has a diameter of 5/16 inches, with 18 threads per inch and the threaded portion of the bo...Read morelt is 0.62 inches long. If the bolt is corroded, the threads are worn down, or the head is damaged or deformed, you will need to replace the bolt to keep your equipment parts secured and functioning efficiently. To replace the bolt, first remove the nut using a wrench or socket. Once the nut is removed, you can unthread the bolt. Insert the new bolt in position, thread the nut on and use a wrench to tighten it. Be careful not to overtighten the bolt to avoid damaging it or stripping the threads. This carriage bolt is sold individually.

It is an authentic component which is specially designed for Little Wonder equipment. This is an identical replacement for a damaged or a missing wheel that was installed on a new unit. It helps to support the equipment allowing for easy transportation. This high-quality wheel assembly is sold as an individual item. Check the diagrams for...Read more your model to ensure the correct repair procedure. A wrench will be needed to replace this wheel. Note, the hardware to secure it is sold separately.

This is a genuine replacement part manufactured for use with outdoor power equipment. The screw includes a lock washer and is commonly used to secure the motor to the frame. This screw has various applications based on the model of the machine it is used with. The screw is sold as an individual replacement part, please see model diagram for part location and usage.

This genuine component is supplied directly from the original equipment manufacturer for use with Ryobi and MTD lawn and garden equipment. It is a standard hardware which may have multiple applications, please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hex washer screw. Ke...Read moreep in mind this high-quality part is made of durable metal and is sold individually.

This is an original replacement part manufactured for use with walk-behind lawnmowers. The metal rope guide mounts to the side rail of the handle, and is secured by a handle knob. The rope guide keeps the starter rope on the upper handle for ease of access, and to keep the rope out of the way while operating. The rope guide is sold individually.

This discharge chute is a genuine OEM sourced replacement part that is specially made for walk-behind lawn mowers. It is mounted to the side of the mower deck to direct the grass clippings away from the unit. This item includes the durable plastic chute with the metal hinge bracket assembly which is used to secure it to the deck. Please n...Read moreote that the hardware to attached this discharge chute is not included, it is sold separately.