My Orders
11B-060A033 (2000) MTD Lawn Mower - Overview
_WW_1.gif "Page A Diagram and Parts List for 2000 MTD Lawn Mower")
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$6.40
In Stock
Lawn Mower Hex Washer Head Screw
Part #710-0599
This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.
Read less
$6.40
In Stock
Bell Blade Support
Part #736-0524B-1
The Blade Support (Bell Blade Support) fits between the bottom of the blade and the blade bolt to provide support for the blade. It is installed underneath the cutting deck on the blade. Installation requires a hammer, 5/8 socket and torque wrench, and is rated as "Easy" by our customers. If broken or damaged (likely due to fatigue) you m...Read moreay hear a rattling sound coming from it, and the part should be replaced. This part is dark gray/silver, individually sold, and measures approx 3.5 x 1.25 inches. Refer to your make, model and diagrams to check if this is the correct part for you.
Read less
$6.40
In Stock
Screw, 3/8-24 x 1.50 (w/25mm Blade Adapter)
Part #710-1044
The hex bolt attaches to the washer and the square key. This part is an OEM from Craftsman for use in snowblowers and lawn mowers. It is available as an individual replacement part and is made of metal. If this item becomes broken or stripped it will need to be replaced and may require a socket set during the installation.
$6.40
In Stock
Hinge Pine
Part #747-0710A
This hinge pin is an OEM part that is designed to hold the chute to the bracket of your lawn mower, allowing the shute to move upward and downward. It is silver, made of metal, and it is around 5 inches in length. Over time, the hinge pin may break, and it will no longer be able to support the chute or allow it to move.
If this occurs, ...Read moreyou will need a pair of needle nose pliers to complete this simple repair, which most of our customers told us was easy. Look for the hinge pin on the chute door and the mounting bracket of your mower deck.
Read less
$6.57
In Stock
Washer-lock 5/16
Part #936-0119
This silver metal lock washer helps prevent the nut on the drive belt pulley shaft from backing off during operation, it has a 5/16-inch inner diameter and a 1/2-inch outer diameter. one washer is included, replace it if fatigue or damage allows the connected shafts to spin freely, verify fit using the equipment model or owner manual
$29.38
In Stock
Use 748-0376c
Part #748-0376E
This OEM keyed blade adapter connects your lawn mower blade to the spindle, enabling it to rotate and cut the grass. It has a length of 1.19 inches, an inside diameter of 7/8 inches, and a bow tie center pattern. If you notice unusual grinding or rattling sounds coming from your mower, or if you feel excessive vibration in the handle or c...Read moreutting deck, it could indicate a broken blade adapter. Similarly, if the blade is not engaging properly or wobbling, it may be a sign that the adapter is worn out and needs replacement. To replace the adapter, start by tilting your machine backward to access the blade. Use a socket or wrench to unscrew the bolt that secures the blade. Then remove the support, blade, and adapter. When installing the new adapter, make sure to align the key on the adapter with the keyway on the shaft. Before operating your lawn mower, ensure that all of the components within the blade assembly are installed properly and securely in place. Please note that this replacement part does not include any accompanying hardware.
Read less
$20.08
In Stock
Cable-throttle 55
Part #946-0671A
This Throttle Control Wire is a 55-inch black Throttle Cable, made of metal with a rubberized casing. It's rated as "Easy" to install, attaching from the throttle control to the carburetor, and requires both pliers and a screw driver. This cable controls the speed of the engine. If broken or damaged (due to typical wear from use) you will...Read more lose control of the engine speed, and the part must be replaced. Refer to your make, model and diagrams to ensure this is the correct part.
Read less
$47.69
In Stock
Control Box-thrott
Part #811-0185
This is a genuine manufacturer-sourced component which is specially designed for lawn mowers. This is the box that the throttle cable is connected to. The cable connects to the carburetor and it stops the engine when you shift the lever to the full choke position. To ensure the correct repair procedure, refer to the appropriate diagrams f...Read moreor your model. Keep in mind this high-quality throttle box is sold as an individual item. It includes the housing, the trigger, and the hardware to secure these components. A screwdriver will be needed to perform this repair.
Read less
$24.06
In Stock
Throttle Hsg. w/o Lever
Part #746-0883
This throttle housing is a genuine OEM sourced item, it is not an aftermarket imitation. It is specially designed use with lawn mowers and snow blowers. Please note, the cable, trigger, spring and the screws are all sold separately. Please note, this plastic housing is sold individually. To complete this repair you will need a screwdriver.
$6.74
In Stock
Screw-hex
Part #710-0654A
This is a genuine replacement part manufactured for use with outdoor power equipment. The screw includes a lock washer and is commonly used to secure the motor to the frame. This screw has various applications based on the model of the machine it is used with. The screw is sold as an individual replacement part, please see model diagram for part location and usage.
$6.40
In Stock
Rope Guide
Part #710-1205
This is an original replacement part manufactured for use with walk-behind lawnmowers. The metal rope guide mounts to the side rail of the handle, and is secured by a handle knob. The rope guide keeps the starter rope on the upper handle for ease of access, and to keep the rope out of the way while operating. The rope guide is sold individually.
$13.27
In Stock
Body-throttle
Part #946-0875
This is an OEM, Yard Machines, Yard Man, Cub Cadet, and MTD part directly sourced from the manufacturer for use in lawn mowers. The throttle body attaches to the throttle lever, the control cable, and the throttle control wire. During replacement, it may require a screwdriver, a set of pliers, and a wrench set to help install this part co...Read morerrectly. It may become broken and will need to be replaced. This is available as an individual replacement part and is made of plastic.
Read less
Watch our pros, then fix it yourself.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More