116-533-135 MTD Lawn Mower - Overview

This carriage bolt measures 5/16-18 x .75 and fastens two parts in your machine together. It has a round domed head and a square underside so the bolt does not rotate once it has been secured into place. If it has signs of deformation or wear, you will need to replace it. To unthread this bolt, you need an adjustable wrench to loosen the ...Read morenut found on the end of the bolt. You may need to apply a lubricating oil to the bolt if it is stuck. You may need to clamp down on the head of the bolt with pliers while continuing to turn the nut counterclockwise. You can then slide the carriage bolt out of its hole or tap it gently with a hammer. This bolt is a standalone product and the nut is not included. This bolt was sourced directly from its manufacturer.

This silver metal lock washer helps prevent the nut on the drive belt pulley shaft from backing off during operation, it has a 5/16-inch inner diameter and a 1/2-inch outer diameter. one washer is included, replace it if fatigue or damage allows the connected shafts to spin freely, verify fit using the equipment model or owner manual

It is an authentic manufacturer-sourced component which is specially designed for lawn and garden equipment. The flange bearing helps to provide a tight fit between connected components. Over time it can wear out, get damaged or lost eventually requiring a replacement. This part is made of high-quality material and is sold individually. C...Read moreheck the diagrams for your model to ensure the exact location and the correct application of this hardware.

This Flat Washer is made of durable gold-colored metal and is an authentic OEM part. It is used to spread the load under a bolt or nut and is sold individually. This part will need to be replaced if you notice any signs of cupping, corrosion, or other damage. Customers rate this repair as Easy.

This special jam nut is sourced directly from the original equipment manufacturer for use with MTD and Ryobi lawn and garden equipment. It is a standard hardware which has multiple applications depending on your tool, please refer to appropriate diagrams for correct location and use of this part. It is made of high-quality metal and it is sold individually.

It is a genuine item that is supplied by the original manufacturer for use with a variety of lawn and garden equipment. A washer is a special part which helps to provide a tight fit between connected components. It is a standard hardware which may have multiple applications. This part provides an identical replacement for a damaged or a m...Read moreissing hardware that was installed on a new unit. Check the diagrams for your specific model for the exact location and the correct application of this flat washer. Note, it is made of durable metal and is sold individually.

This OEM 5 Pin ignition Switch is a silver, steel, individually sold part. It can be installed using a wrench and screwdriver, and has been rated as Easy to install. The part attaches to the dashboard, and is used to start and shut off the engine. If it is broken (likely due to fatigue), you will no longer be able to start or stop your ...Read moreengine and the part must be replaced. Refer to your owners manual or model number to ensure you are purchasing the correct part.

This pair of keys is supplied by the equipment manufacturer for use in lawn and outdoor power equipment. The key is made of metal and designed to prevent unauthorized use or accidental starting of the equipment. It is fitted into the ignition switch, found near the operator seat or control panel. If the key is lost, damaged, corroded or w...Read moreorn down, you will not be able to engage and start the engine. These keys come in a set of two.

This is a genuine OEM sourced replacement screw which is commonly utilized on lawn and garden equipment. It is a standard hardware which has multiple applications based on the model of your unit, please refer to appropriate diagrams for the correct location and use of this part. It is a high-quality hex head screw which is made of durable...Read more metal and it is sold individually. Over time threads may wear out or it may simply get lost eventually requiring a replacement, note that a wrench will be needed to install or remove this hardware.

This Bell-Wash Flat Washer is an OEM part that measures .40 inches I.D. x 88 inches O.D. This washer is a silver, metal, washer sold individually. This part is rated as Easy to install by customers. If missing or damaged (likely due to fatigue) it should be replaced. Refer to your owners manual to ensure this is the correct part for you.

This is a genuine item that is supplied by the original equipment manufacturer for use with MTD and Ryobi lawn and garden equipment. It is a standard hardware which has multiple applications, please make sure to refer to the diagrams of your model for the correct location and application of this item. Keep in mind it is made of durable metal and is sold individually.