114-517A033 (1994) MTD Lawn Mower - Overview

The Lever and Knob Assembly (or Front Wheel Height Adjuster) is used to adjust the front height of the mower, and attaches on the front wheels. It can be installed using a socket set and wrench set, and is rated as "easy" to install by our customers. If broken or damaged (likely due to general wear over time) you will no longer be able to...Read more move it to make adjustments, and the part should be replaced. This black, plastic part is sold individually. Refer to your make, model and diagrams to ensure this part fits your machine.

The hex bolt attaches to the washer and the square key. This part is an OEM from Craftsman for use in snowblowers and lawn mowers. It is available as an individual replacement part and is made of metal. If this item becomes broken or stripped it will need to be replaced and may require a socket set during the installation.

This is the lower handle for various models of walk-behind lawn mowers. This handle is made of durable black metal and attaches directly to the rear of the lawn mower. This handle is an OEM part that is sold by itself and does not come with any hardware or other parts. If your current lower lawn mower handle is corroded or damaged, it nee...Read moreds to be replaced immediately so you can properly and safely handle your lawn mower. This handle measures approximately 24.5-inches long and 17-inches wide and connects the rear of the lawn mower with the upper and main handle that the user holds when operating the lawn mower. Replacing this handle will not require any tools but must start with turning off the lawn mower. Loosen and remove the knobs around the handle, including the ones connecting the lower handle to the mower and those securing the upper and lower handles. Once each knob is removed, replace the old lower handle with the new one, and resecure • all the knobs onto the handle(s).

This replacement shoulder screw is designed to secure push mower wheels to the axle. It is an authentic OEM hardware made out of metal and sold individually. Shoulder bolts are machine screws with an integral shoulder or journal between the head and thread. When installing or removing this shoulder screw you would need a properly sized wrench.

This is a type of handle with a knob-shaped grip used in a variety of lawn and garden tools with adjustable features. This genuine OEM part is 0.8 x 0.2 x 1 inches and is made from plastic. It is designed to connect and disconnect individual parts together without using any tools. By loosening the knob, you can easily adjust the height of...Read more the handles on your equipment to your liking as well as fold the handles for proper storage. Over time the handle knob can wear down or break. If this happens, you will need to unscrew the knob and remove the old rope guide before you can place the new knob on. Place the new rope guide in position, thread the eye of the cable through the eye hook loop and finally thread the new knob on to the shaft and turn it clockwise with your hands until it is secure.

This Throttle Control Wire is a 55-inch black Throttle Cable, made of metal with a rubberized casing. It's rated as "Easy" to install, attaching from the throttle control to the carburetor, and requires both pliers and a screw driver. This cable controls the speed of the engine. If broken or damaged (due to typical wear from use) you will...Read more lose control of the engine speed, and the part must be replaced. Refer to your make, model and diagrams to ensure this is the correct part.

This is a genuine manufacturer-sourced component which is specially designed for lawn mowers. This is the box that the throttle cable is connected to. The cable connects to the carburetor and it stops the engine when you shift the lever to the full choke position. To ensure the correct repair procedure, refer to the appropriate diagrams f...Read moreor your model. Keep in mind this high-quality throttle box is sold as an individual item. It includes the housing, the trigger, and the hardware to secure these components. A screwdriver will be needed to perform this repair.

It is an authentic component which is specially designed for Little Wonder equipment. This is an identical replacement for a damaged or a missing wheel that was installed on a new unit. It helps to support the equipment allowing for easy transportation. This high-quality wheel assembly is sold as an individual item. Check the diagrams for...Read more your model to ensure the correct repair procedure. A wrench will be needed to replace this wheel. Note, the hardware to secure it is sold separately.

This is a genuine replacement part manufactured for use with outdoor power equipment. The screw includes a lock washer and is commonly used to secure the motor to the frame. This screw has various applications based on the model of the machine it is used with. The screw is sold as an individual replacement part, please see model diagram for part location and usage.

This special jam nut is sourced directly from the original equipment manufacturer for use with MTD and Ryobi lawn and garden equipment. It is a standard hardware which has multiple applications depending on your tool, please refer to appropriate diagrams for correct location and use of this part. It is made of high-quality metal and it is sold individually.

This is an original replacement part manufactured for use with walk-behind lawnmowers. The metal rope guide mounts to the side rail of the handle, and is secured by a handle knob. The rope guide keeps the starter rope on the upper handle for ease of access, and to keep the rope out of the way while operating. The rope guide is sold individually.