114-2 - Overview

This Ni Nut-Lock, or Nylock Nut, is a Silver 1/4 x 20 metal nut. Sold individually, it can be adjusted using a wrench or socket and torque wrench to the manufacturer specfications, and is used to secure the sheer pin in place, on the impeller assembly. These nuts are a one-time use part due to their locking mechanism. You'll know the nut...Read more has broken when it appears to have damaged threads or rounded off edges. Customers found this to be an easy repair.

This is an original replacement part sourced directly from the manufacturer. The screw is commonly found in yard equipment from Craftsman, such as lawn tractors, snow blowers, and edgers. This part is made of metal, and may be found in various locations in the machine, depending on model. Please be aware that there are different screws...Read more used in the machine. Refer to the parts diagram to be sure of ordering the correct part. You will require a wrench when replacing this item. The screw is sold as an individual replacement part.

This is a Genuine OEM replacement part used on a variety of Lawn Mowers. This item is made out of Metal and it is Sold Individually. If either the ball bearing or the bearing retainer wear out this will cause the wheels have trouble turning. Ball bearings are used to reduce friction between rotating parts. The balls or rollers take the lo...Read moread and spin, distributing the weight evenly while the minimal contact area of the ball reduces friction. This reduces wear on the tool and allows it to run smoothly. Bearings experience constant wear when the tool is in operation from pressure, heat, vibration and friction. Because of this, many Bearings need periodic maintenance or replacement.

The Lever and Knob Assembly (or Front Wheel Height Adjuster) is used to adjust the front height of the mower, and attaches on the front wheels. It can be installed using a socket set and wrench set, and is rated as "easy" to install by our customers. If broken or damaged (likely due to general wear over time) you will no longer be able to...Read more move it to make adjustments, and the part should be replaced. This black, plastic part is sold individually. Refer to your make, model and diagrams to ensure this part fits your machine.

The hex bolt attaches to the washer and the square key. This part is an OEM from Craftsman for use in snowblowers and lawn mowers. It is available as an individual replacement part and is made of metal. If this item becomes broken or stripped it will need to be replaced and may require a socket set during the installation.

This hinge pin is an OEM part that is designed to hold the chute to the bracket of your lawn mower, allowing the shute to move upward and downward. It is silver, made of metal, and it is around 5 inches in length. Over time, the hinge pin may break, and it will no longer be able to support the chute or allow it to move. If this occurs, ...Read moreyou will need a pair of needle nose pliers to complete this simple repair, which most of our customers told us was easy. Look for the hinge pin on the chute door and the mounting bracket of your mower deck.

This is the lower handle for various models of walk-behind lawn mowers. This handle is made of durable black metal and attaches directly to the rear of the lawn mower. This handle is an OEM part that is sold by itself and does not come with any hardware or other parts. If your current lower lawn mower handle is corroded or damaged, it nee...Read moreds to be replaced immediately so you can properly and safely handle your lawn mower. This handle measures approximately 24.5-inches long and 17-inches wide and connects the rear of the lawn mower with the upper and main handle that the user holds when operating the lawn mower. Replacing this handle will not require any tools but must start with turning off the lawn mower. Loosen and remove the knobs around the handle, including the ones connecting the lower handle to the mower and those securing the upper and lower handles. Once each knob is removed, replace the old lower handle with the new one, and resecure • all the knobs onto the handle(s).

This authentic item is supplied directly from the original equipment manufacturer for use with Toro and Lawn Boy lawn and garden equipment. It is an identical replacement for a missing or a faulty bushing-sleeve that was installed on a new unit, please make sure to check the appropriate diagrams of your model for the correct location and ...Read moreapplication of this hardware. Keep in mind this high-quality component is made of durable metal and is sold individually.

It is a genuine item that is supplied by the original equipment manufacturer for use with Lawn Boy and Toro lawn and garden equipment. This is a special hardware that helps to secure the bushing. It provides an identical replacement for a missing or a faulty part that was installed on a new unit. Please make sure to refer to the appropria...Read morete diagrams of your model for the correct location and application of this retainer. Keep in mind this high-quality part is made of durable metal and is sold individually.

This Throttle Control Wire is a 55-inch black Throttle Cable, made of metal with a rubberized casing. It's rated as "Easy" to install, attaching from the throttle control to the carburetor, and requires both pliers and a screw driver. This cable controls the speed of the engine. If broken or damaged (due to typical wear from use) you will...Read more lose control of the engine speed, and the part must be replaced. Refer to your make, model and diagrams to ensure this is the correct part.