Models > 1130SWE

1130SWE Cub Cadet - Overview

Models starting with 1130SWE

Keep searches simple, eg. "belt" or "pump".
TT Screw 1/4-20 x 0.5 – Part Number: 710-0599
TT Screw 1/4-20 x 0.5
PartSelect #: PS9298768
Manufacturer #: 710-0599
$3.77
  In Stock
Shear Bolt 5/16-18 x 1.5 – Part Number: 710-0890A
Shear Bolt 5/16-18 x 1.5
★★★★★
★★★★★
(1)
PartSelect #: PS10001820
Manufacturer #: 710-0890A
$2.99
  In Stock
Carriage Bolt, 5/16-18 x .75 – Part Number: 710-0451
Carriage Bolt, 5/16-18 x .75
PartSelect #: PS10001568
Manufacturer #: 710-0451
$3.45
  In Stock
Drive Clutch Cable 39.88 – Part Number: 946-0898
Drive Clutch Cable 39.88
PartSelect #: PS9170572
Manufacturer #: 946-0898
$23.91
  In Stock
Auger Clutch Cable – Part Number: 946-0897
Auger Clutch Cable
PartSelect #: PS9170571
Manufacturer #: 946-0897
$22.57
  In Stock
Chute Flange Keeper – Part Number: 731-0851A
Chute Flange Keeper
PartSelect #: PS10005747
Manufacturer #: 731-0851A
$3.81
  In Stock
TT Screw 1/4-14 x .625 – Part Number: 710-1652
TT Screw 1/4-14 x .625
PartSelect #: PS10001918
Manufacturer #: 710-1652
$3.77
  In Stock
Wheel-Friction 4. – Part Number: 935-0243B
Wheel-Friction 4.
★★★★★
★★★★★
(1)
PartSelect #: PS9311064
Manufacturer #: 935-0243B
$16.75
  On Order
Hex Flange Bearing – Part Number: 941-0245
Hex Flange Bearing
PartSelect #: PS9178250
Manufacturer #: 941-0245
$8.86
  On Order
Worm Gear 20 T, 22" – Part Number: 917-04861
Worm Gear 20 T, 22"
PartSelect #: PS9165943
Manufacturer #: 917-04861
$36.96
  In Stock
Washer-Lock 5/16 – Part Number: 936-0119
Washer-Lock 5/16
PartSelect #: PS9311087
Manufacturer #: 936-0119
This Washer-Lock 5/16 is a silver, metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter, it is used to prevent ...
$4.20
  In Stock
Bell. Wash. .340 I.D. x .872 O.D. – Part Number: 736-0242
Bell. Wash. .340 I.D. x .872 O.D.
PartSelect #: PS10006541
Manufacturer #: 736-0242
Sourced directly from the original manufacturer, this Bell Washer is made of gold-colored metal and is sold individually, not as part of a kit or assembly. It is used to provide spacing between variou...
$3.66
  In Stock
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Original shave plate badly worn
With WD-40 or equivalent, spray the four nuts on the underside of the snow blower housing that hold the shave plate to the housing. Also spray the two bolts that hold the shave plate to the side of the housing. Let sit for a few minutes and using a 1/2" box end wrench remove the four nuts on the bottom of the housing. If necessary, apply heat with a torch to loosen. Using a 9/16" box end wrench, remove the nuts on the sides (these also hold the adjustable skid feet). It is recommended that the bottom bolts and nuts be replaced with 5/16-18 X 3/4" long zinc plated carriage bolts using zinc plated washers and ny-lock nuts. It is also recommended that all of th screw threads be coated with an anti- seize lubricant so disassembly at a later date will be easy.
Parts Used:
Shave Plate 26&#34
  • John from HARRISVILLE, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Wrench set
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!