1120 - Overview

The OEM bearing, also known as the flange bearing, is silver, made of metal, and sold individually. It is used on riding mowers to secure the wheel in place and allow it to rotate freely on the shaft. Over time, the part may become worn and damaged, which you will notice if you experience a squealing or grinding sound from the wheel in qu...Read moreestion, or you notice the wheel is sloppy on the shaft. You will need a hammer and punch to complete this repair, which most of our customers rated as easy. Make sure you tap the new bearing into place evenly inside the tire rim.

The Ring Klip Number T5304-75, also known simply as a ring clip, is an OEM part designed to secure your mower wheel to its axle. This part is black, made of metal, and around an inch in length. It is sold individually and may become damaged over time due to wear and fatigue.

This OEM washer, also known as a flat washer, has dimensions of 25/32 x 1-1/4. Silver in color and metal, the washer is sold individually. Although this part can have a range of applications depending on the equipment, its general function is to spread the load under a bolt. Ensure you consult your owners manual or check your model number...Read more to confirm this is the washer you need for your equipment. This part will need to be replaced when your existing one is worn or damaged. It is an easy repair according to our customers, and does not require any special tools.

This is a genuine OEM part made for Craftsman lawn tractors and mowers. Bearings are used to buffer moving parts from damage due to friction. They also stabilize directional movement. Bearings are high-wear parts and are changed regularly. This metal bearing is sold individually. Gauges, washers, rings, etc. sold separately.

The Push Nut is a black, metal nut, which can be installed with pliers and a hammer. It's used to secure parts in place in various locations on a variety of equipment. If damaged will not longer hold in place. Installation is rated as "Easy", but it will depend on the parts your are securing and the equipment you are using. Consult your m...Read moreake, model and diagrams to ensure this is the correct part. The part is sold individually.

E Ring Number 5133-75 is a black, metal ring for securing the position of other parts. If damaged it will become loose or fall off. Installation is rated as "Easy" and is done with a pair of pliers. Refer to your make, model and diagrams to ensure this is the correct part.

This OEM-certified washer provides support, spacing, and reduces friction between parts in your lawn equipment, typically working alongside bolts or screws. This washer has a thickness of 16 gauge and dimensions of 25/32 x 1-5/8 inches. A damaged washer will look deformed or cracked, leading to parts becoming loose or not fitting properly...Read more in your machine. When you remove a broken washer from your machine, you will need pliers or a wrench to loosen the bolt or screw securing it. Once the fastener has been removed, you can pry the washer with a screwdriver. It is important to know that this washer is sold individually. Before adding this replacement part into your cart, check your instruction manual to determine the number of washers your machine needs.

This is an original part from Husqvarna. The hood latch is constructed of flexible plastic, and is made for use with many riding lawn mowers. This component is fastened onto the lower bagger chute, latching it to the upper chute. The hood latch is sold individually. A pair of pliers and a screwdriver may be helpful for the removal and replacement.

This metal square key is designed to prevent the rear wheel of your lawn equipment from slipping. Approximately sized at 3/16 x 2, it fits into the groove found on the axle and the hub of the wheel, ensuring proper alignment of the two parts. If the machine becomes hard to turn or maneuver or it makes a grinding or clicking sound, your sq...Read moreuare key may be worn out. Visually inspecting this part for bends and cracks can confirm this. You may also notice that the rear wheel is wobbling or falling off. A worn square key can cause damage to the wheel assembly of the machine, leading to costly repairs or even the need to purchase a new one. To prevent that, you need to replace a broken square key as soon as possible. Replacing the square key is a simple process. After turning your lawn equipment off and letting it cool down, you need to use a jack to lift the rear of it off the ground. Remove the wheel from the axle by using a socket to remove any bolts or nuts holding it in place. With pliers, you can then take the square key off the machine. This replacement part is sold individually and is sourced directly from its original manufacturer.

It is a genuine manufacturer-approved part which is specially designed for use with Poulan, Weed Eater and Husqvarna riding lawn mowers and garden tractors. The purpose of the interlock switch is to act as a safety feature which will shut the engine off if the driver leaves the seat. Unfortunately, over time parts will wear out and it may...Read more begin to fail eventually requiring a replacement. Refer to the owners manual and the appropriate diagrams of your model for the correct location and installation of this component. Note, this high-quality plastic body switch is sold individually. You may need a screwdriver and pliers to perform this repair.

It is an authentic replacement cap-spindle that is supplied by the original equipment manufacturer for use with Poulan, Ryobi and Husqvarna riding lawn mowers and garden tractors. It is an identical replacement for a missing or damaged cap that was originally installed on a new equipment. The cap is utilized to cover the spindle. Make sur...Read moree to check the appropriate diagrams of your model for the exact location and application of this hardware. This high-quality cap-spindle is made of durable plastic material and is sold individually.

This is an authentic replacement part sourced directly from the manufacturer. The return spring is commonly found in Craftsman lawn tractors and riding mowers. This part is made of metal, and is generally used to apply tension to the idler arm. You may require pliers when replacing this item. The return spring is available as an individual replacement part.