112-098R7 MTD Lawn Mower - Overview

The Lever and Knob Assembly (or Front Wheel Height Adjuster) is used to adjust the front height of the mower, and attaches on the front wheels. It can be installed using a socket set and wrench set, and is rated as "easy" to install by our customers. If broken or damaged (likely due to general wear over time) you will no longer be able to...Read more move it to make adjustments, and the part should be replaced. This black, plastic part is sold individually. Refer to your make, model and diagrams to ensure this part fits your machine.

The hex bolt attaches to the washer and the square key. This part is an OEM from Craftsman for use in snowblowers and lawn mowers. It is available as an individual replacement part and is made of metal. If this item becomes broken or stripped it will need to be replaced and may require a socket set during the installation.

This is the lower handle for various models of walk-behind lawn mowers. This handle is made of durable black metal and attaches directly to the rear of the lawn mower. This handle is an OEM part that is sold by itself and does not come with any hardware or other parts. If your current lower lawn mower handle is corroded or damaged, it nee...Read moreds to be replaced immediately so you can properly and safely handle your lawn mower. This handle measures approximately 24.5-inches long and 17-inches wide and connects the rear of the lawn mower with the upper and main handle that the user holds when operating the lawn mower. Replacing this handle will not require any tools but must start with turning off the lawn mower. Loosen and remove the knobs around the handle, including the ones connecting the lower handle to the mower and those securing the upper and lower handles. Once each knob is removed, replace the old lower handle with the new one, and resecure • all the knobs onto the handle(s).

This Washer-Lock 5/16 is a silver, metal part that is sold individually and comes direct from the manufacturer. With a 5/16 Inch Interior Diameter and 1/2 Inch Outside Diameter, it is used to prevent the nut from backing off and becoming loose on the pulley shaft, and is attached to the drive belt pulley assembly. You will know if you nee...Read mored this because your owners manual will specify it, or the model number of your machine will correspond with this part. If the part is broken due to fatigue, the shafts will free spin when they should be locked together, and must be replaced.

This Throttle Control Wire is a 55-inch black Throttle Cable, made of metal with a rubberized casing. It's rated as "Easy" to install, attaching from the throttle control to the carburetor, and requires both pliers and a screw driver. This cable controls the speed of the engine. If broken or damaged (due to typical wear from use) you will...Read more lose control of the engine speed, and the part must be replaced. Refer to your make, model and diagrams to ensure this is the correct part.

This is a genuine manufacturer-sourced component which is specially designed for lawn mowers. This is the box that the throttle cable is connected to. The cable connects to the carburetor and it stops the engine when you shift the lever to the full choke position. To ensure the correct repair procedure, refer to the appropriate diagrams f...Read moreor your model. Keep in mind this high-quality throttle box is sold as an individual item. It includes the housing, the trigger, and the hardware to secure these components. A screwdriver will be needed to perform this repair.

It is an authentic component which is specially designed for Little Wonder equipment. This is an identical replacement for a damaged or a missing wheel that was installed on a new unit. It helps to support the equipment allowing for easy transportation. This high-quality wheel assembly is sold as an individual item. Check the diagrams for...Read more your model to ensure the correct repair procedure. A wrench will be needed to replace this wheel. Note, the hardware to secure it is sold separately.

This is a genuine OEM sourced replacement part that is intended to be used with walk-behind lawnmowers from MTD, Yard Machines, Bolens, and Yard-Man. The wheel attaches to the height adjustment plate at the front of the mower. The wheel is used to provide traction to allow the mover to move across the lawn.

This is a genuine replacement part manufactured for use with outdoor power equipment. The screw includes a lock washer and is commonly used to secure the motor to the frame. This screw has various applications based on the model of the machine it is used with. The screw is sold as an individual replacement part, please see model diagram for part location and usage.

This is an original replacement part manufactured for use with walk-behind lawnmowers. The metal rope guide mounts to the side rail of the handle, and is secured by a handle knob. The rope guide keeps the starter rope on the upper handle for ease of access, and to keep the rope out of the way while operating. The rope guide is sold individually.

This operator presence cable is a genuine OEM replacement designed for walk-behind lawn mowers. It connects the handle bail to the engine brake system, ensuring the engine stops immediately when the handle is released for safe operation. Built for reliable performance with correct cable length and fittings, it’s an ideal replacement when ...Read morethe mower won’t shut off properly or the original cable is stretched, frayed, or broken.

This is an OEM, Yard Machines, Yard Man, Cub Cadet, and MTD part directly sourced from the manufacturer for use in lawn mowers. The throttle body attaches to the throttle lever, the control cable, and the throttle control wire. During replacement, it may require a screwdriver, a set of pliers, and a wrench set to help install this part co...Read morerrectly. It may become broken and will need to be replaced. This is available as an individual replacement part and is made of plastic.