EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

110S-6070 Kenmore Washer - Overview

Diagrams for 110S-6070

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer Shaft Seal – Part Number: WP91939
$9.62
In Stock
Washer Shaft Seal
★★★★★
★★★★★
(1)
Part #WP91939
This OEM upper transmission shaft seal, also known as the oil seal, is found in your washers and dryers. It acts as a barrier to prevent water from leaking into the transmission assembly. It measures 1/2 inch in height with a 1-inch diameter, and is located at the top of the transmission shaft where it enters the tub. Signs of a broken seal include water stains, dampness, or pooling of water beneath the appliance. If left unreplaced, it can result in water damage to internal components, along with the potential for corrosion, mold growth, and unpleasant odors. To remove the shaft seal, consult your user guide for specific instructions. Start by shutting off the power and water supply. Remove the water hoses and drain hose, being cautious of any water that may leak out. You will need tools like a putty knife, screwdriver, nut driver, pliers, spanner, plastic mallet, and a socket set. Open the lid and proceed to remove the agitator assembly, detach the control panel, and disconnect any necessary wiring harnesses. Remove the cabinet and water break. Continue disassembling the inner tub until you can lift it out of the appliance and tilt it onto its back, propping it up with a block. This will allow access to the transmission assembly from beneath the appliance. Remove the mounting fasteners on the pump to reach the motor assembly. Once the motor assembly is out, further disassemble it to access the basket drive. The seal can be removed from the top of the shaft of the drive tube, below the thrust ring. When purchasing parts for your appliance repair, it is important to remember that your appliance uses various seals and gaskets. It is important to ensure that you purchase the correct part when making repairs.
Washer V-Style Cogged Tooth Pump Belt – Part Number: WP95405
$28.42
In Stock
Washer Ringwire – Part Number: W11033823
$11.77
In Stock
Washer Ringwire
Part #W11033823
This is part of the Basket Drive and found under the Brake Lining parts.
BEARING – Part Number: 285205
$9.62
Special Order
BEARING
Part #285205
Belt Drive Motor Kit with Capacitor – Part Number: 285222
No Longer Available
Belt Drive Motor Kit with Capacitor
Part #285222
This two-speed motor performs 1725 revolutions per minute in one speed, and 1140 revolutions per minute in the other speed. It runs at 1/2 horsepower and carries 115 volts.
BEARING – Part Number: 350920
$11.77
Special Order
BEARING
Part #350920
BAR-CAM – Part Number: 18642
No Longer Available
BAR-CAM
Part #18642
BULK OF 100 PCS.
RUBBER GROMMET – Part Number: 19138
No Longer Available
RUBBER GROMMET
Part #19138
PULLEY, MAIN DRIVE – Part Number: 360840
No Longer Available
PULLEY, MAIN DRIVE
Part #360840
DISCONTINUED – Part Number: 285068
No Longer Available
DISCONTINUED
Part #285068
MOTOR-DRVE – Part Number: 386614
No Longer Available
MOTOR-DRVE
Part #386614
SPRING, DRIVE – Part Number: 19049
No Longer Available
SPRING, DRIVE
Part #19049

Common Symptoms of the 110S-6070

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
It was the heat safety switch in the old drive motor
2 of 3 people found this instruction helpful.
  • Andrew from HATTIESBURG, MS
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
It was fairly easy a few tight spaces to reach in but all in all it was pretty straight forward
Was this helpful?
Thank you for voting!
Washer Had A Continuous Moan And Vibration
  • Roger from Millis, MA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Wrench set
I disconnected the drive belt from the motor and ran the motor to isolate it from the rest of the mechanisms. This was the noise. I disconnected the water lines and electrical cord,laid the machine front down. I disconnected the motor plug,removed the two bracket to body bolts and lifted the motor out to the bench. I then transferred th e bracket to the new motor and reversed the procedure to install the motor. The most difficult part was raising the machine back up alone,I suggest a helper.
Was this helpful?
Thank you for voting!