1103401796 Kenmore Dryer Parts & Repair Help | PartSelect
Models > 1103401796

1103401796 Kenmore Dryer - Overview

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(76)
PartSelect #:PS334310
Manufacturer #:279834
This is an M series new style coil kit, used in gas dryers. When the igniter reaches a high enough temperature, these coils work together to let the gas enter the dryer. The coils ...
$15.07
In Stock
(17)
PartSelect #:PS334180
Manufacturer #:279311
If your dryer will not heat, takes too long to dry, or does not provide enough heat, you might want to replace your igniter kit. This silicone carbide igniter with ceramic holder k...
$40.20
In Stock
(8)
PartSelect #:PS11741429
Manufacturer #:WP338906
If your gas dryer is not heating up or igniting, then replacing the flame sensor, located in the burner assembly, could solve it. This part senses heat from the igniter to monitor...
$28.40
In Stock
PartSelect #:PS11743791
Manufacturer #:WP694424
The leak limiter or natural gas limiter is used in dryers. This part acts as a cover of the adjustment screw on the pressure regulator. If you are changing from propane (LP) back t...
$18.28
In Stock
PartSelect #:PS11743784
Manufacturer #:WP693995
$4.97
In Stock
PartSelect #:PS11743790
Manufacturer #:WP694423
$4.97
In Stock
PartSelect #:PS11743789
Manufacturer #:WP694422
$17.34
In Stock
PartSelect #:PS3500824
Manufacturer #:W10402145
$63.40
In Stock
PartSelect #:PS3505737
Manufacturer #:W10295523
$16.21
Special Order
PartSelect #:PS334264
Manufacturer #:279734
$301.16
In Stock
Questions and Answers for 1103401796
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Dryer ran but would not heat

  • Customer: Gary from Haverhill, NH
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 350 of 389 people found this instruction helpful
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of t... read more

Dryer flame goes out after about 8-minutes from start and won’t work again until a 15-minute rest.

  • Customer: andy from Bethesda, MD
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 162 of 86 people found this instruction helpful
There was no problem with lint build-up within the dryer & the exhaust vent. I removed the gas cycling thermostat & thermal fuse from system & dryer still was not operating correctly. The radiant sensor & hi-limit thermostat both seemed to be operating correctly. That left either of the two coils as the culprits. I replaced both coils & the problem was co... read more

Timer wasn't working (New Timer)

  • Customer: Joaquin from Las Vegas, NV
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 142 of 81 people found this instruction helpful
Timer wasn't working on the regular cycle so I replace it with a new one from partselect. It still wasn't working so I ordered and replace the cycling thermostat, the thermal fuse I also cleaned the vent and dryer it still didn't work so I read the diagram for the electrical and found that a coil for the gas valve is line with timer. I ordered the coils for ... read more