Models
>
11028102310
11028102310 Kenmore Washer - Overview
Sections of the 11028102310
[Viewing 5 of 5]Keep searches simple, eg. "belt" or "pump".
Hose Clamp
PartSelect #: PS11743008
Manufacturer #: WP596669
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
$11.80
In Stock
Lid Lock Assembly
PartSelect #: PS11756782
Manufacturer #: WPW10619844
This part makes sure that the lid is shut before allowing the machine to start or agitate.
NOTE: This is a manufacturer substitution. Part may differ in appearance but is a functional equivalent to prior parts including
$94.96
In Stock
Screw
PartSelect #: PS11742721
Manufacturer #: WP488729
Metallic screw that is less than an inch long. Does not include the plastic washer.
$7.91
In Stock
Touch-Up Paint - White
PartSelect #: PS385132
Manufacturer #: 72017
This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is...
$8.00
In Stock
Lid Hinge Mounting Screw
PartSelect #: PS11748588
Manufacturer #: WPW10119828
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
$11.80
In Stock
Hinge
PartSelect #: PS11746532
Manufacturer #: WP8563964
This is a replacement lid hinge for your washer. It is approximately 2.5 inches in length and 1.5 inches in width. The lid hinge is what the lid for your washer pivots on. If the lid hinge is damaged,...
$8.00
In Stock
Spray Paint - 12 oz. - White
PartSelect #: PS347819
Manufacturer #: 350930
Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to...
$22.68
In Stock
Water Inlet Valve
PartSelect #: PS11731257
Manufacturer #: W10853723
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
$152.28
In Stock
Single Hex Head Screw
PartSelect #: PS11742731
Manufacturer #: WP489069
Sold individually. The size of this screw is 1/4" hex head and 10-12 x 1/2".
$5.42
In Stock
Hose Washer Kit
PartSelect #: PS1803069
Manufacturer #: 285452A
Washer fill hose gasket and screen. This is a set of 4.
$8.28
In Stock
Affresh Washing Machine Cleaner - 3 pack
PartSelect #: PS1960673
Manufacturer #: W10135699
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
$12.60
In Stock
Questions And Answers for 11028102310
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Sort by:
- < Prev
- 1
- 2
- Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Laurie
March 19, 2020
Washer has sd code and will not spin
For model number 11028102310
Good Day Laurie. Thank you for your question in regards to your unit (Model Number 11028102310). Based on our research, the SD error code indicates suds have been detected in your washer. We recommend that you use a HE low sudsing detergent. This code can also indicate that there are too much soap or the wrong kind of soap was used in the washer (we suggest reviewing the owner's manual for more information in regards to this). Finally, this code could be an indication that the drain pump is restricted or the drain hose is kinked. We hope this helps! Best Regards.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Moises
October 16, 2022
I have a Kenmore Series700
TYPE:580
MOD 110.28102310
SER C41770918
I put it in a light load normal spin cold water normal soil level it did successfully go through prewash cycle and also wash cycle, but got stuck in Rinse cycle with 27 min remaining and had a code LD
I unplugged washer for 5-10 min and tried the drain/spin cycle to drain water and doesn’t let me use any options until disconnected
For model number 11028102310
Hello Moises, thank you for a very interesting question. We have researched your model and found that the issue is probably with the Drain Hose. Check to make sure the drain hose isn’t clogged. If that does not take care of the issue, then the problem is most likely to be related to the Drain Pump, part number PS11754363. If you require assistance to place an order, please contact customer service. We hope that helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Michael
December 19, 2022
It is not the too much suds thing. It is the part that makes the drum spin. It agitates but fails the spin cycle. The drum sits on the piece that locks into the drum to make it spin. I need that part only
For model number 11028102310
Hi Michael, thank you for reaching out. The part you are looking for is the drive shaft. It is not available separately and is only available as a part of the tub seal and bearing kit, part number PS3503261. Customer service is always available to help you place an order if you are having trouble doing so. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Helaine
November 30, 2019
This washer really smells. I see residue building up around the outer ring of the tub. I use the recommended washing machine cleaner. Can we take it apart and see where the smell is coming from. Thank you.
For model number 11028102310
Hi Helaine, you can watch a video we have that will will shoe you how to take a back panel off here: https://www.youtube.com/watch?v=9qpUhb1zBYs. Thank you for your question and good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Paul
April 23, 2023
It keeps giving a uL code, is there a belt or something that may have come loose? The tub is moves a lot more now. The only way it does not give the code is if it is empty. I didn't see a belt on the drawings, but the tub is very unstable
For model number 11028102310
Hello Paul, thank you for contacting us. If uL appears in the display, the load is out of balance. The washer is running a load-balance correction routine. Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press the start button. If the problem persists, you may need to replace the suspension rod kit, part number PS2355518. We hope this solves your problem!
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- 2
- Next >
Common Symptoms of the 11028102310
[Viewing 4 of 4]Leaking
Fixed by
these parts
these parts
Show All
Lid or door won’t close
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Locking Issues
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Parts Used:
-
Michelle from Richardson, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
64 of 125 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Lid Lock broke
Followed video from you tube. Man made it look very easy. Not! Hole that lock has to come through in back was very tricky. Also, DO NOT THROW OUT OLD PART UNTIL NEW ONE IS INSTALLED. The reason for that is there is a CLIP at the end of the old part that is needed to attach new part to wire section in control panel. NO WHERE is it m
... Read more
entioned at you got the clip from the old part. Luckily we saved it. Without that clip, you are screwed.
Read less
Parts Used:
-
Judith from SAYRE, PA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers, Socket set, Wrench (Adjustable)
11 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer would not start due to lock mechanism turning on and off.
-
Dyleena from HOUSTON, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
15 of 26 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!