Your coupon for will be reflected when you check out!
✖
Your coupon for
✖
Hello!
You're visiting the PartSelect site in U.S.
Would you like to shop on the Canadian site?
Stay on this site
Go to Canadian site
✖
Model Number Locations
1Select Category Type
Select Category Type
2Select Product Type
Select Product Type
3Select {MODEL} Type
Select {MODEL} Type
Sample Model Number Tags
Model numbers can be made up of numbers (1005400, for example) or a combination of letters and numbers (LAT1000AAE). The model number will most likely appear on either a paper sticker or a metal plate. Your appliance's model number tag may look similar to the sample model number tags shown here (model number highlighted in yellow):
Model has been saved to My Models. If you're not signed in, your lists are available on this device and will expire within 30 days.
Model has been saved to My Models.
This splutch cam kit is a genuine replacement assembly designed for select Whirlpool, Maytag, and affiliated brand washing machines. It plays a critical role in the wash and spin cycles by engaging th...
This washer lid switch is a critical safety component designed to halt the spinning motion of the tub when the lid is opened. Its primary function is to prevent accidental contact with moving parts du...
This suspension rod kit is a genuine OEM kit specially designed for washing machines. Each kit includes a set of 4 rods, 4 suspension balls and 4 bushings. The suspension rods are responsible for supp...
This genuine OEM drive belt is designed to transfer power from the motor to the drum in select Whirlpool, Maytag, Kenmore, and other compatible washing machines. Operating at 115 volts and 60 Hz, the ...
This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This ...
This shift actuator is a genuine replacement component designed for top-load washing machines. It plays a critical role in transitioning the washer between agitation and spin cycles by shifting the tr...
This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid latch is damaged, you...
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installat...
$9.62
In Stock
Order now and your part arrives by May 14
Questions And Answers for 11021302012
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Alexander
February 11, 2025
Hello,
I have Kenmore washer model 11021302012. Washer makes a terrible grinding noise right before a spin cycle (trying to spin). No spin issue if laundry is completely taken out. In this case drain/spin cycle completes just fine with no noise. No problems with other modes.
Just trying to figure out which part is failing. I think it could be a drive pulley, belt, shift actuator or gearcase itself.
For model number 11021302012
Hi Alexander,
Thank you for your question. If you hear a grinding noise from the washer when it is use, the bearing on the gearcase, part number PS12347614, is either worn or damaged and the gearcase will need to be replaced. We hope this helps!
Model number 110.21302012 machine does spin and drain, but not every time. If its a larger load the machine stays in spin mode and the only way to complete load since it is soaking wet, is to switch mode to drain and spin. This happens always when on the regular wash mode. I now have to wash clothes in the express load in very small loads to complete a cycle, but it still on occasion will not be able to spin and drain all the water, then again having to use the spin and drain mode to complete the cycle.
For model number 11021302012
Hello Brian,
Thank you for your question. Our sources suggest there is an issue with the control board when it is changing cycles, it is not advancing correctly. You would need to replace the control board under part PS3653305 for your model to fix the issue. We hope this helps!
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer faile
... Read mored which would not let the machine come up to maximum spin speed. The tachometer is part of the solenoid actuator that shifts the transmission. It is not specifically called out in the manual. Any failure causes the lid lock light to blink which gives the appearance of a lid lock failure
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this inform
... Read moreation the installation was simple. Remove the clamps and the back of the console, slide the top forward and lift, remove and replace the lock and reassemble. You don't even have to remove the hoses.
