1102011200A Kenmore Washer Parts & Repair Help | PartSelect
Models > 1102011200A

1102011200A Kenmore Washer - Overview

Manuals & Care Guides for 1102011200A

Click to download
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(270)
PartSelect #:PS388034
Manufacturer #:80040
This kit is used for replacing the agitator directional cogs (Agitator Dogs, Agitator Repair Kit, Washer Agitator Dogs, Agitator Dog Ears). The agitator is what creates the thrusti...
$4.32
In Stock
(139)
PartSelect #:PS1485646
Manufacturer #:285753A
This direct drive motor coupling (Direct Drive Washer Motor Coupling, Motor Coupling, Washer Motor Coupling, Coupling Kit) provides a cushioned connection between the transmission ...
$23.15
In Stock
(81)
PartSelect #:PS11741239
Manufacturer #:WP3363394
The direct drive drain pump (Whirlpool Direct Drive Washer Pump, Drain Pump, Washer Drain Pump, Water Pump) removes water from the washer during the drain cycle without the use of ...
$41.31
In Stock
(72)
PartSelect #:PS11722098
Manufacturer #:3949247V
This switch (Lid Switch Assembly With Leads, Washer Lid Switch, Lid Switch Assembly, Washer Lid Switch) tells the washing machine that the lid is closed, which allows the wash cycl...
$46.44
On Order
(25)
PartSelect #:PS11743345
Manufacturer #:WP63907
The suspension spring supports the outer tub and keeps the tub steady during loads that could cause an unbalance. If this part breaks, is worn down or has stretched out and lost it...
$4.80
In Stock
(107)
PartSelect #:PS334646
Manufacturer #:285805
The water inlet valve on your washing machine is used to fill the tub with cold, warm, or hot water for the wash and rinse cycles. This part could have either a blue or green-color...
$33.92
In Stock
(59)
PartSelect #:PS334641
Manufacturer #:285785
A clutch assembly (Clutch, Washer Clutch) is found in your washing machine and is responsible for spinning the basket during the spin cycle. The clutch lining can wear over time. I...
$49.12
In Stock
(5)
PartSelect #:PS334562
Manufacturer #:285587
This is a genuine OEM thrust spacer for your washer, and is also commonly known as a retainer ring. The spacer is about 2.5 inches in diameter, is made of plastic, and is white in ...
$5.20
In Stock
(9)
PartSelect #:PS11741866
Manufacturer #:WP358237
This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".
$7.48
In Stock
(15)
PartSelect #:PS11751118
Manufacturer #:WPW10250667
This tub spring is also known as suspension spring, balance spring, or counterweight spring. It is sold individually. The function of the part is to counterbalance the weight of th...
$7.48
In Stock
Questions and Answers for 1102011200A
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer stopped mid cycle

Lid Switch – Part Number: 3949247V
  • Customer: Travis from Pearland, TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1002 of 1026 people found this instruction helpful
1. Unplug washer.
2. Remove screws at control panel end caps.
3. Flip control panel back to expose wiring.
4. Detach lid switch wiring harness from control panel.
5. Use screwdriver to pry the 2 brass clips holding the back panel of the washer to the front and sides piece.
6. Tilt the front/sides piece over to expose lid switch.
read more

No movement from Basket & agitator

  • Customer: Jeff from Wayne, NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1014 of 1075 people found this instruction helpful
The job looked intimidating but turned out to be very easy.
First take off the water pump by removing the two clips that hold it in place. Place a shallow pan under the pump to catch the water that is in the pump and hoses. Open the hose clamps with a pair of pliers or channel locks (better) and slide the hoses off of the water pump.
The motor co... read more

washer wouldn't agitate

  • Customer: mike from Kent, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 825 of 873 people found this instruction helpful
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing usin... read more