11020102311 Kenmore Washer Parts & Repair Help | PartSelect
Models > 11020102311

11020102311 Kenmore Washer - Overview

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
(29)
PartSelect #:PS3497627
Manufacturer #:W10404050
The point of the lid switch is for the tub to stop spinning when the washer lid is opened. It is a safety precaution just in case someone decides to stick their hand inside the wa...
$44.97
In Stock
(2)
PartSelect #:PS11746840
Manufacturer #:WP90767
This screw is sold individually.
$7.76
In Stock
(16)
PartSelect #:PS11747978
Manufacturer #:WPW10006384
The main drive belt is designed to ride on the pulley until the basket gets up to speed.
$33.88
In Stock
(16)
PartSelect #:PS10057144
Manufacturer #:W10721967
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch...
$46.30
On Order
(2)
PartSelect #:PS11740613
Manufacturer #:WP285655
The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washe...
$8.60
In Stock
(2)
PartSelect #:PS11748588
Manufacturer #:WPW10119828
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
$7.76
In Stock
(1)
PartSelect #:PS11746209
Manufacturer #:WP8536939
This insert is sold individually. Knob not included. Knob is sold separately.
$8.60
In Stock
(18)
PartSelect #:PS11757114
Manufacturer #:WPW10683603
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount o...
$89.44
In Stock
(16)
PartSelect #:PS11747977
Manufacturer #:WPW10006355
This part changes the transmission from agitation to spin mode. This actuator is for washers. Actuator shifts the splutch and monitors the position of the splutch.
$54.22
In Stock
(6)
PartSelect #:PS11750882
Manufacturer #:WPW10240513
This part is the replacement lid latch or latch assembly for your top-load washer. The lid latch holds your washer door closed, and allows the washer to run its cycle. If the lid l...
$33.50
In Stock
Questions and Answers for 11020102311
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Lid Lock light blinking, machine will not start

  • Customer: David from Los Alamos, NM
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 289 of 359 people found this instruction helpful
A detailed Service Technician Service Manual is hidden inside the machine on the front panel. It is hidden by the bleach dispenser input. It gives a list of fault codes and instructions for calibration after repair, resetting fault codes, and a manual test mode for stepping the machine through each mode on command. The Tachometer failed which would not le... read more

Defective lid latch - Cabrio Washer

Lid Latch Assembly – Part Number: W10404050
  • Customer: William from Wakefield, RI
  • Difficulty: Very Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 69 of 83 people found this instruction helpful
The instructions that came with the part were worthless. Essentially, unplug, put in new part, plug it back in. I spent a considerable amount of time on the internet and finally found a video showing how to open the top. Unlike other models, it is held down by clamps in the back rather than clips in the front. Once finding this information the installati... read more

Noise on bottom of Washer louder as time went on. 1 1/2 years

  • Customer: Jerry from WALLA WALLA, WA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 48 of 62 people found this instruction helpful
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so yo... read more